安规网

 找回密码
 注册安规
安规论坛 | 仪器设备 | 求职招聘 | 国家标准 公告 | 教程 | 家电 | 灯具 | 环保 | ITAV 签到 充值 在线 打卡 设备 好友| 帖子| 空间| 日志| 相册
IP淋雨机 | 证书查询 | 规范下载 | 资质查询 招聘 | 考试 | 线缆 | 玩具 | 标准 | 综 合 红包 邮箱 打卡 工资 禁言 分享| 记录| 道具| 勋章| 任务
水平垂直燃烧机 | 针焰 | 灼热丝 | 漏电起痕
IP防水防尘设备|拉力机|恒温恒湿|标准试验指
灯头量规|插头量规|静风烤箱|电池设备|球压
万年历 | 距元旦节还有
自2007年5月10日,安规网已运行 天
IP淋雨设备| 恒温恒湿箱| 拉力机| 医疗检测设备耐划痕试验机|可程式恒温恒湿试验箱 | 耦合器设备水平垂直燃烧机|灼热丝|针焰试验机|漏电起痕试验机
灯头量规|试验指|插头插座量规|灯具检测设备耐划痕试验机|可程式恒温恒湿试验箱 | 耦合器设备广东安规-原厂生产-满足标准-审核无忧
楼主: sclongwar

[IEC标准产品] 功率计算问题

[复制链接]
发表于 2008-4-9 17:37 | 显示全部楼层
广东安规检测
有限公司提供:
看到这段话了啊
发表于 2008-4-9 17:50 | 显示全部楼层
不好意思,没说完 3 I( C$ \6 B( Z6 u2 O, l* N0 Z
5.12说的是通用情况,既然5.13特意提出了PTC发热元件,那么似乎应该按照5.13来,不是吗?这两节似乎是有点矛盾.......
发表于 2008-4-10 07:33 | 显示全部楼层
并不矛盾.
' R. u( c9 p4 m3 v) M15.2 前面是对"器具必须在输入功率乘以一个系数条件下"试验要求的适用性规定.0 `/ F. P4 {2 ?3 ~9 e
15.2后面是PTC以外有明显温度系数电阻电热元件的试验做法,15.3是对PTC电热元件相应的试验方法,
发表于 2008-4-10 09:18 | 显示全部楼层
标准规定:
$ S0 P( n9 {# X6 @6 a3.1.4rated power input/ w. }0 n1 b+ n% D* x0 F, G
power input assigned to the appliance by the manufacturer
/ t! G" u' N' ]& [: {0 S# a( V7 @+ S; R; e- Y
5.8.2 Appliances having more than one rated voltage are tested on the basis of the most unfavourable voltage.' H3 ~5 ~& f5 _# X# o( ?  }6 x
For motor-operated appliances, and combined appliances, marked with a rated voltage range, when it is specified that the supply voltage is equal to the rated voltage multiplied by a factor, the appliance is supplied at
: k, ]! h. t& w" Q6 p$ x9 S– the upper limit of the rated voltage range multiplied by this factor, if greater than 1;
; B3 w. }. A+ {– the lower limit of the rated voltage range multiplied by this factor, if smaller than 1.
  k" x0 n, m- n4 RWhen a factor is not specified, the supply voltage is the most unfavourable within the rated9 u7 `* h& }- ~; [2 G* f6 l
voltage range.
# }4 B9 M  M# p7 @3 E9 \NOTE 1 If a heating appliance has a rated voltage range, the upper limit of the voltage range will usually be the most unfavourable voltage within the range.
) L3 C: H- D2 J% g, y2 E3 G& z11.4  Heating appliances are operated under normal operation and at 1,15 times rated power input.
- V0 G/ s. ^/ B+ W  h19.2 Appliances with heating elements are tested under the conditions specified in clause 11
" B0 j( r! E; Gbut with restricted heat dissipation. The supply voltage, determined prior to the test, is that
7 M" ~, [/ Q% r' |- _% xrequired to provide a power input of 0,85 times rated power input under normal operation
  S: b3 E; v% X5 f. M/ h* cwhen the power input has stabilized. This voltage is maintained throughout the test.
+ O" ^( q1 e& I) O$ v所以个人认为:19.2与19.3的测试电压应该是:测得额定功率0.85与1.24倍时的电压即可.
+ n0 p3 o% V1 Z7 o1 N( X-----------个人理解错误了,这是指额定电压是单电压的情况
发表于 2008-4-10 10:53 | 显示全部楼层
引用第42楼caballo3157于2008-04-10 07:33发表的  :$ [3 S1 }2 F6 {0 G& [
并不矛盾.
4 i5 r: v) f; }; o5 u& m; E5.12 前面是对"器具必须在输入功率乘以一个系数条件下"试验要求的适用性规定.
4 }7 `/ ]6 G+ @8 x: s% I% d6 K5.12后面是PTC以外有明显温度系数电阻电热元件的试验做法,5.13是对PTC电热元件相应的试验方法,
所以说在做PTC发热器的时候,还是以5.13为准嘛,1 h4 h1 V  j9 ~- ?" s
那么之前和boom的讨论还是有意义的
发表于 2008-4-11 22:20 | 显示全部楼层
请问系数是怎么确定的?
发表于 2008-4-15 15:46 | 显示全部楼层
这样一来是不是19.2和19.3时带PTC的也是以根号输入功率的系数再X额定电压=?V,然后以此电压测试啊
发表于 2008-11-25 12:31 | 显示全部楼层
问题是当针对PTC heating element,5.13 只针对了系数大于1的情况,即系数的平方根乘以电压,但没有讲当输入功率系数小于1的情况,请问小于1的情况怎么讨论?即19.2,0.85P的测试应该怎么做?
发表于 2008-11-25 12:43 | 显示全部楼层
做19.2时,按照0.85×(220 / 230 )^2×2400W来测试。
 楼主| 发表于 2008-11-25 12:44 | 显示全部楼层
针对PTC, 如果系数大于1, 即用系数的平方根乘以电压, 当输入功率系数小于1, 直接用系数乘以功率.也就是19.2时, 按照0.85倍 额定功率来做.
您需要登录后才可以回帖 登录 | 注册安规

本版积分规则

关闭

安规网为您推荐上一条 /1 下一条

QQ|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网 ( 粤ICP13023453-10 )

GMT+8, 2026-10-29 02:16 , Processed in 0.103520 second(s), 17 queries .

Powered by Discuz! X3.4

© 2001-2023 Discuz! Team.

快速回复 返回顶部 返回列表