问:澳洲插座

gdt102

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

As/NZS 3112上有关于Marking的具体要求，请见如下：
" ?, P$ _- Z: v) ^* k3 `7 [/ d0 z# n* V2.12.1 Required marking
; U( v9 P3 ?5 pThe plug shall be marked with the following information in accordance with AS/NZS 3100:
(a) The name, trade name, or mark of the manufacturer or of the responsible vendor.
6 S" N- t* T* I/ H+ ^' {7 q( x. v) m) w(b) The current rating in amperes.
3 J# l, M% X) P; z& t7 u# I(c) The voltage.
(d) If not the only type of plug marketed by the manufacturer or responsible vendor, the
plug shall also be marked with a catalogue number, type number or name, or other
marking which will distinguish it from any other plug marketed by that manufacturer or responsible vendor.
(e) Any IP rating, if claimed.
" |2 F5 c) U% }; oNOTE: Manufacturers making a statement of compliance with this Australian/New Zealand
& ^% r( a' G8 YStandard on a product, packaging, or promotional material related to that product are advised to ensure that such compliance is capable of being verified.

/ e7 h( n, d% w3 V2.12.2 Location of marking
$ @  _* e3 G7 N" \The marking required by Clause 2.12.1 shall be located as follows:
(a) Items (a) and (d)—on any portion of the plug.
6 u) i. r& w' Y1 h7 p' Y(b) Items (b), (c) and (e)—on the external body of the plug.

maisie

1。澳洲插座未要求带保护门；
; n) p( M& _' m! p# V2。电流值，两芯八字插的电流为up to 10A，则我认为是可以为7.5A的；
3。标志：标识插头型号、厂标、额定电压、电流和证书号即可

billma

澳洲移动式多位插座外壳一般用什么塑胶？需要做125度球压吗？

honry

关于澳洲插座的防火问题是：老是听说要求要达到960-glow-wire test
3 C, f% Q( M1 [: G% X% y% Q???请问谁知道具体的要求啊，是否另外有文件说明了？？？？谢谢！

孟云房

楼上的问题是针对澳洲拖线板类产品的，
& ^$ W( R2 v/ i4 Y. F适用标准是AS/NZS 3105,
论坛内可以搜索到该标准。
只是对特殊材料和特殊部件才适用960度灼热丝试验，
$ B( I; a* _+ ^4 U普通带电部件支承件要求是850度。

) R9 t0 B0 h4 ~8 N! ?8.9 Determination of ignitability and combustion propagation
& |* v0 k$ Z) X8 K6 s3 LThe EPOD shall comply with the requirements for resistance to fire in accordance with
AS/NZS 3100:2002 Annex A. The glow-wire test temperature ‘T’ shall be 850°C. However,
$ C, ]3 B$ C- W8 |7 B) ^for any styrenic material or any material of an undeclared type, the test temperature ‘T’
) n- K7 N7 Y2 v: k4 Zshall be 960°C.
! f* P6 k$ m) {8 tAny overcurrent protective device shall be subjected to the glow-wire test with a test
temperature of 960°C.