问:澳洲插座

gdt102

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

As/NZS 3112上有关于Marking的具体要求，请见如下：
6 V. ]# ?! t# Y) r. g! O2.12.1 Required marking
The plug shall be marked with the following information in accordance with AS/NZS 3100:
3 J# b& \3 r) Q2 h0 ~! \(a) The name, trade name, or mark of the manufacturer or of the responsible vendor.
: M* D3 I; Z9 J% b: w(b) The current rating in amperes.
(c) The voltage.
+ N+ |7 K2 B  [( n) j(d) If not the only type of plug marketed by the manufacturer or responsible vendor, the
/ W, |9 [4 Q' G' H% t' gplug shall also be marked with a catalogue number, type number or name, or other
$ W% v! ]9 d& bmarking which will distinguish it from any other plug marketed by that manufacturer or responsible vendor.
) P( J; R# T; a6 }1 y% [/ `8 n(e) Any IP rating, if claimed.
NOTE: Manufacturers making a statement of compliance with this Australian/New Zealand
- f  z1 s& t% @1 v% m8 K* ~Standard on a product, packaging, or promotional material related to that product are advised to ensure that such compliance is capable of being verified.

2.12.2 Location of marking
2 N2 M. l) p2 g5 W! tThe marking required by Clause 2.12.1 shall be located as follows:
8 j+ j' s+ Z7 Y* p- ^(a) Items (a) and (d)—on any portion of the plug.
) V2 `' S4 O$ o8 ~' i(b) Items (b), (c) and (e)—on the external body of the plug.

maisie

1。澳洲插座未要求带保护门；
2。电流值，两芯八字插的电流为up to 10A，则我认为是可以为7.5A的；
0 D$ c9 d. U7 B  t3。标志：标识插头型号、厂标、额定电压、电流和证书号即可

billma

澳洲移动式多位插座外壳一般用什么塑胶？需要做125度球压吗？

honry

关于澳洲插座的防火问题是：老是听说要求要达到960-glow-wire test
???请问谁知道具体的要求啊，是否另外有文件说明了？？？？谢谢！

孟云房

楼上的问题是针对澳洲拖线板类产品的，
% s; U. U+ h* x4 _' A适用标准是AS/NZS 3105,
4 V3 ?- m, j5 i; k" W: Q4 s论坛内可以搜索到该标准。
; A: {$ J+ c( W/ k+ d3 H$ B9 s只是对特殊材料和特殊部件才适用960度灼热丝试验，
普通带电部件支承件要求是850度。

8.9 Determination of ignitability and combustion propagation
The EPOD shall comply with the requirements for resistance to fire in accordance with
% T9 F' |4 ^; s& wAS/NZS 3100:2002 Annex A. The glow-wire test temperature ‘T’ shall be 850°C. However,
for any styrenic material or any material of an undeclared type, the test temperature ‘T’
shall be 960°C.
Any overcurrent protective device shall be subjected to the glow-wire test with a test
% h3 B8 Y& @! p0 l0 L" T5 F3 _4 Jtemperature of 960°C.