950中变压器过载

安规007 · 发表于 2011-6-9 15:41

貌似就是泛指的，我一直没能找出相关的决议。

aiduoxi · 发表于 2011-6-9 15:56

过载其实也可以在前端电路加以控制，这只是我个人见解
快一年没接触开关电源了

安规007 · 发表于 2011-6-9 16:05

仔细看Annex C 中的C.1 overload test,
C.1 Overload test
If the tests in this clause are conducted under simulated conditions on the bench, these
conditions shall include any protection device that would protect the transformer in the
complete equipment.
Transformers for switch mode power supply units are tested in the complete power supply unit
or in the complete equipment. Test loads are applied to the output of the power supply unit.
A linear transformer or a ferro-resonant transformer has each secondary winding loaded in
turn, with any other secondaries loaded between zero and their specified maxima to result in
the maximum heating effect.
The output of a switch mode power supply unit is loaded to result in the maximum heating
effect in the transformer.
NOTE For examples of loading to give the maximum heating effect, see Annex X.
Where an overload cannot occur or is unlikely to create a hazard, the above tests are not
made.
最后这句话：Where an overload cannot occur or is unlikely to create a hazard, the above tests are not made.
我觉得可以作为不用做过载的依据。

琥珀流云 · 发表于 2011-6-9 16:20

呵呵这种初级变压器很常见啊,我的理解是不用做过载.首先我们明白为什么要做过载,就是考量变压器在过载情况下,是否会造成过温,破坏绝缘等等.初级变压器跨接的只是功能绝缘.
标准里面有一句话:Where an overload cannot occur or is unlikely to create a hazard, the above tests are not made. 有些夸接加强绝缘的变压器也可以不做过载,要分析这组线圈是否会发生过载现象.

fanfei0428 · 发表于 2011-6-9 17:00

满足功能绝缘就可以了

		自动登录	找回密码
密码			注册安规

	安规论坛 \| 仪器设备 \| 求职招聘 \| 国家标准		公告 \| 教程 \| 家电 \| 灯具 \| 环保 \| ITAV		签到充值在线打卡设备		好友\| 帖子\| 空间\| 日志\| 相册
	IP淋雨机 \| 证书查询 \| 规范下载 \| 资质查询		招聘 \| 考试 \| 线缆 \| 玩具 \| 标准 \| 综合		红包邮箱打卡工资禁言		分享\| 记录\| 道具\| 勋章\| 任务

IP淋雨设备\| 恒温恒湿箱\| 拉力机\| 医疗检测设备	ASTC+那尔｜沙特SASO Saber GCC 埃及COC	水平垂直燃烧机\|灼热丝\|针焰试验机\|漏电起痕试验机
灯头量规\|试验指\|插头插座量规\|灯具检测设备	耐划痕试验机\|可程式恒温恒湿试验箱 \| 耦合器设备	广东安规-原厂生产-满足标准-审核无忧

[电源产品] 950中变压器过载