摇头风扇，电源软线

hexiling

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

看你做的对应的标准需不需要，标准上要求，就要做---不知道你是做内销还是外销？

nancyzyh01

之前做过风扇的测试，如果是摇头风扇，和电源线关系不大，也就是电源线不会做弯曲实验，因为风扇的头在摆动时电源线是跟着摆动，是通过机械连接，转轴里面的配线跟着转动的幅度也不大，但是针对厂家，需要做寿命进行验证，经过X次循环后，有没有异音，或者卡死现象等等。

Andy.Yang

引用第2楼wxy810626于2010-07-07 09:47发表的  :
3 ~3 P! ~# o$ F4 y
7 ^' M; F' r' W6 L0 I8 c8 hHi, Andy, 你的这个观点我不太同意.
电源线供应商的测试只能当作参考,关键是我们自己要进行确认.

Couldbe, you are right if you wanna double check if there is a question with some components, but how you can imagine, there are so many components in a complex final products, so we can let the provider to do some tests which we wanna do, but this action normally, is guaranteed by a third party or some approval agency. For example, if the flexible cords/power supply cords have already aproved by UL or some other approval agencies, then this flexible test, or some tests kind of this must be done when the manufacturer apply for the approval...That's what I mean.

杨柳风

引用第12楼Andy.Yang于2010-07-07 13:32发表的  :

Couldbe, you are right if you wanna double check if there is a question with some components, but how you can imagine, there are so many components in a complex final products, so we can let the provider to do some tests which we wanna do, but this action normally, is guaranteed by a third party or some approval agency. For example, if the flexible cords/power supply cords have already aproved by UL or some other approval agencies, then this flexible test, or some tests kind of this must be done when the manufacturer apply for the approval...That's what I mean.

当然, 我们没有必要去做那么多测试, 我们只要测试和我们相关的测试即可以,比方说如要做电源线摇摆测试,我们肯定不相信供应商提供的测试报告,我们必须自己测试其符合要求才可以.

Andy.Yang

引用第14楼wxy810626于2010-07-07 14:04发表的  :
/ W2 W6 z: m2 l( s. Z/ c! ?
  A( ]; B2 d, F: Q当然, 我们没有必要去做那么多测试, 我们只要测试和我们相关的测试即可以,比方说如要做电源线摇摆测试,我们肯定不相信供应商提供的测试报告,我们必须自己测试其符合要求才可以.

perhaps, if your products' standard requires you to do some tests(type test, routine test), but it's for the final product, not for its components...

杨柳风

引用第15楼Andy.Yang于2010-07-07 15:09发表的  :

. ?1 }1 a* Y; S; i6 K3 C8 Fperhaps, if your products' standard requires you to do some tests(type test, routine test), but it's for the final product, not for its components...

Agree with your opinion, so I think the cord flexing test should be performed at the poster's side not at the supplier's side.

Liu

是否要做测试？楼主没说明出口地，UL的请参考UL507，似乎与摇头没有关系：
14.1.1A A power supply cord supplied with an appliance as described in Table 14.1, rows 1 and 2, shall
5 c  J8 _2 ]( m, Balso comply with the performance test requirements of Sections 51B – 51E.
3 X5 m( f3 D( p2 ~
51B Supply Cord Abrasion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
& O5 `( D* [0 [; W" m5 I, H' S' Y51C Supply Cord Pinching – Mandrel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92A
4 `! P2 ~5 @( P" I( v5 ^% c' ~8 S51D Supply Cord Crushing – Mandrel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92C
0 m9 o) ]( f5 y$ H51E Supply Cord Flexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92D

5 ^: W" f) I+ ]5 x( Z2 f/ e51E Supply Cord Flexing
! D, J; Z5 R6 P4 b! Q  b
& S+ x" s8 Y9 d1 u51E.1 Six samples of a power-supply cord shall be subjected to the test specified in 51E.2 – 51E.6. Upon
completion of the test, there shall not be:
a) Development of an open circuit,
: G4 t& Y& c# h% H# U: _b) Breakage of more than 10 percent of the strands of any conductor,
0 \  C2 G7 a; z* Y" d; }c) Broken strands piercing the insulation and becoming accessible,
6 I8 O3 L6 Q9 K3 k& i+ n9 p, N6 Gd) Cracking or degradation of the cord insulation, or
6 K0 G7 b$ L) i) ne) Exposure of the internal shield of a leakage current detector-interrupter.
% h9 P" d; f, ]# X2 X51E.2 With reference to 51E.1, conductors include grounding conductors. A short circuit between
conductors of the cord is determined when, any time during the test, the current exceeds a value equal
( ^# l8 N" g3 Fto twice the rated current of the appliance.
51E.3 Each supply cord sample is to be mounted through a slot in the L-bracket of the test fixture shown
in Figure 51E.1. The L-bracket is to measure 38.1 mm (1.5 inches) deep and 38.1 mm high and shall be
) P+ r1 n/ ^! M. N1 z, P" h+ C- kprovided with a slot having dimensions as shown in Figure 51E.2. The cord shall exit vertically through
the top surface of the bracket base and shall be routed across a curved surface for attachment, see Figure
, f; I* t6 W/ ]51E.3.

Liu

其实这个flexing test与电线有无认证无关。比如UL1017的吸尘器，同样是要摇摆测试的，为什么？因为吸尘器在使用过程中会经常弯折电线。明白UL1017的要求，UL507的要求不难理解：
5.16A Power-supply cord flexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
) k2 o! D8 r0 g* w5.17 Wire flexing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

一概认为零部件有UL认证就可以豁免测试，这是一个很大的误区，专标很多会根据产品的实际情况做一些特别的测试，所以很多时候就会考虑到部件的可接受性（condition of acceptable），简称COA。其实就是考察部件的suitable。Recoginzed的部件很多是不一定可接受的。