本帖最后由 wawyp 于 2012-2-23 18:51 编辑 ; `& O! t+ m$ z7 ^: @0 d
$ ^9 S# ~# p& Y- n& c4 Z [此为一adapter,Rated input: 100-240V 0.35A 50/60Hz Single Phase
% C/ u, N+ N3 k3 I: V3 L" U5 `9 [ Rated output: 5V 2A
% ^) u# x- E/ ~9 R" p* o Maximum Output Power: 10W
% }0 y5 i: E5 K. P3 Z; V4 j C: V Maximum Ambient: 40 C(度)
1 Y# m; `. `, ?2 \$ [6 S: ~2 ^3 F希望安规前辈能对data sheet中的点进行讲解(标准的理解,本项测试的本质,每项被测数据的测试方法,仪器选用的原则,测试过程中的注意事项),以供大家交流讨论以及新人学习之用,谢谢!
( k8 h& S% [. {& H, z
! E2 G! M+ J/ G3 e' q a$ C) A, s此节有2个版本data sheet,都放上来/ V4 N1 ~# k$ |# O0 B8 _; h
二.1
+ ?. w5 Y- S' ]0 {1.5.7.4, 2.4.2 – DOUBLE OR REINFORCED INSULATION BRIDGED BY COMPONENTS This test was conducted after Electric Strength Testing of the insulation. METHOD The unit was connected to ___ [V ac, __ Hz ] [V dc]. An IEC leakage current meter described in Annex D of UL 60950 and a switch were connected with the bridging component __CY1__ , The measured current was recorded. Measuring instrument used for test: Annex D.1 – Simpson 228 ! F% K5 b8 }6 ~/ E# W) a4 ?) y3 R
[ ] Other__________________ [ ] Annex D.2 – [ ] Simpson 229 -2 [ ] Other__________________ Measurements were made under both normal and single fault conditions as notes below. Y1 Capacitors were subjected to single fault conditions. RESULTS Location ( Component ) : CY1 8 M% D m1 @+ |- e# i* I3 s
The circuit”s available current [ complied ] [ did not comply ] with the current limits of 0.5mA rms ( 0.7 mA pk) 3 X: e6 n! U- d( v8 v6 {' p
NOTES TO LAB: 1. The current measured through the bridging component and the Annex D measuring instrument shall not exceed 0.5 mA ( 0.7 mA pk). NOTES TO ENGINEER: 1. Components subjected to single component fault conditions include IEC 384 -14, U, Y, Y2 or Y4 capacitors, or resistors which bridge double or reinforced insulation. IEC 60384 -14, Y1 capacitors were not faulted.
1 {& z8 g+ U1 o, G8 F( | 二.2 1.5.7.4, 2.4.2 – DOUBLE OR REINFORCED INSULATION BRIDGED BY COMPONENTS This test was conducted after Electric Strength Testing of the insulation. METHOD PART1 The unit was connected to ___ [V ac, __ Hz ] [V dc]. A 2000Ω non-inductive resistor and a switch were connected between the load side of the bridging component __CY1__ , and [ protective earth ] [ neutral ]. A storage oscilloscope was connected across the points under consideration. The switch was closed and the following values were recorded: V p – Peak V dc – dc Voltage A p – Peak current = V p/2000 dc – dc current = V dc/2000 kHz – Circuit frequency in kilohertz In addition, a photograph or the waveform was made. Measurements were made under both normal and single fault conditions as notes below. Y1 Capacitors were subjected to single fault conditions. RESULTS PART1 Location ( Component ) : CY1 to [ protective earth ] [ neutral ] Condition | Volts , peak | Volts , dc | mAp | mA ,dc | Frequency kHz | Normal | | | | | | | | | | | | | | | | | |
The circuit”s available current [ complied ] [ did not comply ] with the current limits of a Limited Current Circuit. |