求助：BS1363-2 中的第13.11章节测试是怎么做的?

defong

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

BS1363-2 中的第13.11章节测试是怎么做的。给一个3F的力怎么判定结果是否合格？假定现在我把开关的触点焊接在一起，让它处于闭合状态，再给操作件施加3F的力，但操作件能停留在OFF的位置，那这个产品是不是判定为不合格呢？有人能把具体的操作方法说一下吗，请赐教，非常感谢！

bs1363

Your method for doing the test is correct. If the actuating member remained at rest in the OFF position, it should be classified as "Fail". The purpose of this test is to make sure that no wrong indication ("On" state become "Off" but the socket is still in "On" state) will be given to end user.

defong

引用第1楼bs1363于2010-12-14 11:45发表的  :
; y, I# h4 r/ n0 j# oYour method for doing the test is correct. If the actuating member remained at rest in the OFF position, it should be classified as "Fail". The purpose of this test is to make sure that no wrong indication ("On" state become "Off" but the socket is still in "On" state) will be given to end user.

thanks a lot, will you show us some pictures for operating this test?

defong

1楼朋友的意思是说。如果我把触点焊接起来。然后用施加3F的力，样品还是不能停留要OFF位，正常情况下，它应该会自动复位到ON的位置。。。不知道这样理解对不对

bs1363

Your understanding is correct.
At first, you should measure the force F for operating the actuting member (switch). Then, you should calculate the exact force (3F). If the force (3F) is less than 50N, then you should use a force of 50N for the test. If the force (3F) is greater than 100N, then you should use a force of 100N for the test.

defong

引用第4楼bs1363于2010-12-23 15:32发表的  :
( W$ @/ P' C* y' TYour understanding is correct.
( X: H7 q# O6 ?* o2 UAt first, you should measure the force F for operating the actuting member (switch). Then, you should calculate the exact force (3F). If the force (3F) is less than 50N, then you should use a force of 50N for the test. If the force (3F) is greater than 100N, then you should use a force of 100N for the test.

thanks a lot.