|
|
Tensile Stress, brk, Type I, 抗張強度2 M' H' |" S& O+ y( @6 ?
Tensile Strain, brk, Type I, 拉伸變形3 r: O+ f5 _" S6 l8 v
Flexural Modulus, 彎曲模量1 K! U+ O+ j6 [, s1 j
Hardness, Shore A, 硬度(肖氏)
5 f- d! J' B1 U2 ^5 g8 PTensile Stress, break, 抗張強度
/ }* l9 N; |7 xTensile Strain, break, 拉伸變形
( b8 w. O) w" s5 C! tFlexural Modulus, 彎曲模量' K5 K, g8 E# }! P
IMPACT3 e4 s/ F; s1 W+ N% k
Brittleness Temperature 脆裂溫度
8 A. R; T2 }8 z1 \; S4 k$ H9 ]1 \PHYSICAL" A3 R* s: a) Y. h; G, Y
Specific Gravity 比重& h" j4 d% s1 r0 f5 ~ F
Melt Flow Rate, 熔融指數9 r5 M6 q* T: Y5 J
ELECTRICAL& q+ w- t2 N3 e) n- j2 L; j' u
Volume Resistivity 體積電阻
- N( P7 w$ J; s( F( f! R) k9 \Relative Permittivity, 介電常數% E+ B% c1 u) C6 H
Dissipation Factor, 損耗角9 f+ L0 z! R9 b
Dielectric strength in oil, 油中介電強度4 n3 e/ t' a8 ?& I
Comparative Tracking Index 比較留痕指數(CTI)
* k. ]5 Z1 i2 z7 o8 W: M. i. x" gFLAME CHARACTERISTICS
/ X" r1 }+ e7 e- ]Smoke Density on 0.5mm plaque, Non-flame, Ds, 無焰式煙密度
; p# D# q. Q0 W* N) F* R3 e QSmoke Density on 0.5mm plaque, Flame, Ds, 有焰式煙密度7 o% y0 O# r8 i- `9 I
Glow Wire Flammability Index 960°C, passes at 3 mm 灼絲燃燒指數
7 A T# q% Q dGlow Wire Ignitability Temperature, 3.0 mm 800 °C 灼絲引燃溫度: J9 T# X5 ~5 ]9 i
Oxygen Index (LOI) 氧指數3 K- b9 a. a, H5 D$ W; h0 \
WIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper4 E7 Z# n) g. T; E. ~* N) _
Tensile strength @ break 抗張強度! y- T# U; J7 y+ ?7 C2 N4 x. F) E# \
WIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper, S7 ]& m) f8 V- B* L
Tensile elongation @ break 伸長率
& f$ Z3 ?- `( A" H! L# ZTensile strength @ break after 7days @113°C 化後抗張# }. t; p# w0 I+ z4 C
Tensile elongation @ break after 7days @113°C 化後伸長
) o, A: K& L6 f; ]2 ?7 ^! TUL temperature rating 80 °C UL 額定溫度
# q7 G( u6 R2 `6 Y, P& P) v: uHeat Deformation at 100°C/250g 加熱變形: f1 b! D+ n+ S" x) _$ t
VW-1 Pass - UL 1581% c$ s2 K! J; c
" d" \) c2 B, I1 n0 {. `( _2 U
Drying Temperature 干燥溫度
3 m6 ]$ z" Q8 F/ i. {, i& TDrying Time 5 - 7 hrs干燥時間
1 e1 W1 M8 a+ a4 X( X9 ^. mDrying Time (Cumulative) 12 hrs干燥時間4 o, `' }/ H/ ^2 U
Maximum Moisture Content 0.02 %最大濕度含量6 r4 Y. G- ~0 p- e' B
Extruder Length/Diameter Ratio (L/D) 22:1 to 26:1 -押出長徑比
4 E* H2 a# E! y! [2 {/ TScrew Speed 15 - 85 rpm螺杆轉速" w. h# X6 l% s1 w, F
Feed Zone Temperature 180 - 230 °C輸料段溫度4 n. f, _4 P( \( O0 }. V: c/ C
Middle Zone Temperatures 230 - 260 °C中段溫度
' L: Z) [. A. I2 i0 YHead Zone Temperature 230 - 260 °C頭部溫度7 U$ O0 U; O% b1 C
Neck Temperature 230 - 260 °C機頸溫度
( Z- J5 W% t3 u% J w, q6 U" R' _Cross-head Temperature 230 - 260 °C機頭溫度2 \# \; H2 @* X6 H7 x2 e
Die Temperature 230 - 260 °C眼模溫度+ Z. Y3 M7 O8 p' R: E
Melt Temperature 230 - 260 °C熔融段溫度: A. Z; V& P0 Y9 D4 b
Conductor Pre-heat Temperature 25 - 120 °C導體預熱溫度
) g0 g( Q. A3 l& sScreen Pack 150 - 100 -網目" ]' k% T d9 {; x, J
Cooling Water Air Gap 100 - 200 mm冷卻水間距3 \$ \1 }/ q: |- ~
Water Bath Temperature水浴溫度 |
|
/1 
|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网
( 粤ICP13023453-10 ) 
窥视卡
雷达卡
发表于 2009-7-24 21:02
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
抢沙发
千斤顶
显身卡