UL1598 15.2 Non-IC 温升测试问题

Mark.Li

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

8 c; w6 D2 C2 n/ k+ G  请教各位下？UL1598 第15.2章节中的异常温升测试怎么理解？特别是15.2.6 求大师们解读下？

15.2.3 For ceiling-mounted luminaires, the thermal insulation specified in Clause 19.16 shall be placed
around the luminaire in the test box as follows:
" l( U, m2 q& Q  {# G, j(a) the initial depth of the thermal insulation shall be 100 mm (4 in) above the bottom of the
8 U) g1 R- @/ Z% F4 Ptest box or 50 mm (2 in) above the lowest glass portion of the test lamp, whichever is higher;
(b) the initial depth of the insulation shall not exceed the height of the lamp compartment; and
(c) if more than one test iteration is required to achieve the results specified in Clause 15.2.7,
an additional 50 mm (2 in) of thermal insulation shall be added for each successive iteration.
- C' n7 P5 M% _' K8 j& g6 D* kThe last increase in thermal insulation may be less than a 50 mm (2 in) increment, to ensure
9 F+ i$ p/ {) v( Rthat the maximum 216 mm (8.5 in) height requirement is not exceeded. For each additional
2 x3 N& y* Y: w4 z: bthermal insulation level, the test shall be restarted with all temperatures at room ambient.
( q. \' p( k9 Q, b6 f. s# ^SEPTEMBER 17, 2008 NMX-J-307/1-ANCE ¨ C22.2 NO. 250.0-08 ¨ UL 1598 151
5 `2 h6 I+ Z! x; i$ d% \15.2.4 For recessed wall-mounted luminaires, the thermal insulation specified in Clause 19.16 shall be
placed over a recessed luminaire mounted in the test wall so the topmost portion of the luminaire is under
216 mm (8.5 in) of thermal insulation.
15.2.5 The test lamp type and wattage for:
5 H+ E; T9 i$ Z9 \( g" s# l(a) an incandescent luminaire shall be as marked on the luminaire and as specified in Clause
19.8 and Table 19.8.2; and
(b) an HID luminaire shall be as marked on the luminaire and ballast, and as specified in
Clause 19.8.
15.2.6 A luminaire shall be operated until the thermal protector trips or for a maximum of 7.5 h. If the
protector does not trip within 3 h, the test shall be repeated with an additional 50 mm (2 in) of thermal
$ L% P8 B: `4 W0 x) r" E4 Tinsulation, until:
(a) the thermal protector trips within 3 h; or
(b) the temperature limits in Table 14.1.2 are exceeded; or
  [/ W$ A$ _' x) o6 W(c) the thermal insulation height is 216 mm (8.5 in) above the highest projection of the
luminaire, the thermal protector does not operate, and the temperature limits are not exceeded,
in which case the test shall be repeated with the next hotter trim installed.
8 l# k0 m! l) C8 E15.2.7 Test results shall be acceptable if the thermal protector:
(a) operates within 3 h and no part of the luminaire in contact with thermal insulation or the test
; T5 s* n5 V) hbox exceeds 160 °C; or
(b) does not operate within 3 h and the temperature limits specified in Table 14.1.2 are not
exceeded during the test. Any part of the luminaire in contact with thermal insulation or the test
+ _. E+ a7 z1 |7 {box shall not exceed 90 °C. The test shall be terminated after 7.5 h.

5 k9 m) D( P* i2 A) j) p

Mark.Li

怎么没人回答呢？

Mark.Li

求人指点

jayjie729

基本原则就是，做异常时最好选用一个性能好的温控器，在首次加入隔热棉时就3H内动作，测试就OK了，不然50mm重复添加隔热棉很难保证外壳温度不超过限制。

Mark.Li

写的真麻烦。前后矛盾费事。加一次就够了。还要加多少次。