|
| DSH 7004 S# G# a/ s" Z8 i# Y* y$ }
# [! U. @& k7 X: _: T
| Push force for connectors
0 v4 @- t+ j, d5 w | 4.3.5- U+ X7 E% J6 o* }' p
| 60950-1(ed.2)1 k, Y) r+ Q7 ?9 n7 o4 Q9 p' q
|
$ c' G; G- A3 YStandard- No. Year$ _7 c: X( S' q+ ~
IEC 60950-1:2005 DSH
/ @$ G. \# N2 F- s8 {; A9 s- K2 ]0700
! F. X% X# u$ h: f; L& o2008% h! |2 I' X0 i/ N9 r8 D
Category: OFF2 l3 O1 n0 K" F9 R* x1 h4 g
Subclause:
( v$ Z: C. Z. u9 F" `: T. n4.3.5% x; W! Y5 b/ ` `3 m+ m( u9 w
Developed by: ETF 2% O3 H1 S3 p# z" H
Subject:
3 u8 i6 q& ~4 E1 D* W2 t' mPush force for connectors' Z4 V5 W% V' q* W, S; R# }. [' Y
Key words:( ]) d. E8 g D* m( }0 `% q
-Travel adapter;
# D; @2 \, L3 n( x2 ]8 Q0 Q1 a- connector misconnection
; C+ u V! T9 q. D4 u8 CDecision approved at the
/ D6 G. U; Y0 H1 J, u) e3 W) o+ T9 A46th CTL Plenary Meeting
- F! T! \* }- Xin 2009
/ ?( Z7 C5 K4 r6 E {/ t0 ^Question:) k3 X5 T2 u. ^, w: \6 w
A travel adapter consists of two separable parts:
) X- C* g: F4 M' i& i2 X- {' t· AC/DC unit (down transformation of voltage, safety separation provided)
' X( v5 K' h' c: n: ?· DC/DC unit with output cable (supply stabilization and voltage adjustment, no safety separation
) W1 v8 n$ Z/ Jprovided). l) l# k) T) b. w% m
The unit can be used at AC mains (both units connected together) or DC (units separated, only DC/DC4 T! v/ h3 E8 J& \$ m j
used). The AC/DC unit has a (Class II) IEC 60320-1 type appliance inlet; the DC/DC unit uses a0 F) ~. k4 T5 E- W% |
special 2-pins input connector.$ E# Z! f8 ~' J I! O; d
With a small force applied (less than 30 N) an IEC 60320-1 coupler can be inserted into the input- m4 Y5 G4 i5 |, G! w# A ^1 \
connector of the DC/DC unit and make contact.
4 t- M- J* }6 z1 R+ r7 c$ s0 da. Is such design acceptable if a warning label is provided on the DC/DC unit and additional remarks, x+ Y& R3 h0 m" t# ?$ r- @4 X
are provided in the user manual that state that the connector of the AC power cord shall not be( N2 g+ \* [8 ^" E9 R- R
pushed into the input connector of the DC/DC unit?
B! z; J& ^( }& Ib. How much force must be applied during the testing of the input connector (DC) and appliance
, C# \, ^+ m5 Xcoupler (AC)?
- {: T* g* |* [4 O1 Q& v2 v& BDecision:1 [1 }7 \6 h$ R2 h& t
A test force of 60 N (as specified in IEC 60320-1, no safety factor considered) shall be applied when
; w* I! ^6 e2 e, itesting possible misconnection of IEC 60320 and similar connectors.
0 d+ t1 k% h0 A
. L* m' ~, _ B, |3 H9 h* c/ z+ k9 [8 B0 U! P
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|