|
# T# \5 m' L: `# P: s3 |0 j7 c
6 F% y3 u+ V5 ~1 h | Mains Transformers
0 s5 Q4 ]5 a0 s+ f8 a | 14.7
8 M$ _1 \' e7 i0 S | 61010-1(ed.1);am1;am2
C7 ]7 ^9 I8 R2 O0 A | - R- x, W2 o5 m# B/ @( S6 Q3 L
& _3 u g% F* O& WStandard:
( F4 x, X' B+ A* Q/ M1 O7 ]7 D. r" z cIEC 61010-
6 O# H9 t" y G8 Z* ]9 E1:1990+A1:1992+A2:1995
, M3 O" [% B/ VSub clause:8 X, E2 ?- F3 s, F5 W5 d
14.7. M5 ^, O* \. [# D; |" Z5 k
Sheet n. 315
8 ^) b& R8 B- v& S: V6 L+ A/ ^Page 1(1)$ v' p9 s, g" {# c: I7 F8 k
Subject:
* M- o# n% K j: b7 |$ _1 _0 J& rMains transformers# f. b% M! p9 L+ M8 Y4 S7 S( ^
Key words:5 r. ~$ ` k' p7 F$ L+ I
Transformer1 v6 i. a. y% A- y" K4 h- F
Approval* F( ~1 L3 M4 {. P4 N
Decision taken by
/ b/ a7 w; h+ R @ tETF3 and confirmed
7 V. q3 w \% \) c) S6 yby CTL at its 38th5 m X. W$ f/ m% H1 D
meeting, in Toronto7 o( S7 p0 B" w2 X' w$ F! G7 X$ X
Question:
h1 X: W7 }' }, k4 kWhere a transformer is certified to IEC 60742, should further examination and test be
: t' n! t% ~* xperformed ?
; g' o4 `+ a4 Y, E7 Q) @Note that IEC 60742 has been withdrawn and replaced by IEC 61558 series.- t) m" \9 t, V" j9 f
Decision7 y# t+ _' q0 F- l6 z# t
The entire equipment needs to be in conformity with IEC 61010-1. To achieve this,
# { C, F( V `! i1 c, _ zrecognition should be given to those features of the device which meet these requirements
3 R% i3 B4 T' E+ ?and are recorded in the approval report. Other features not covered should be examined for7 L- p* y0 x/ _
the application concerned.
2 H$ o% F8 w8 V3 _+ tExplanation5 R, r; h) S& k+ q, S; O: X1 s
There is not at this time, a common set of requirements for all transformers, power supplies0 ?/ E) x# }* ^+ p0 ~; G8 D
and so on, laboratories must, therefore, consider the application of each device for the use it T L$ I$ W; F% G
is employed in the equipment.! I# k1 X0 }; n& [! }* a
2 F( U5 \9 R9 D0 G2 w4 {0 B4 m" n
. I+ X& Q; D* {& S7 C' Z' W3 z2 l6 U0 y0 z3 ~" Q ?
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册安规
x
|