|
| DSH 7574 n3 I# F1 Z# ?+ k, \
1 k3 C- U$ W) X
| Surface tension requirement for wet leakage current test# i, d$ l$ X! O
| 10.15.2.a)! L8 l- w* B( P: T; g" w# v( q
| 61215(ed.2)
& U6 i$ z( ` p4 y# q | 3 G' I) o+ \3 p0 v$ t
Standard(s)- (incl. year) O+ J ~* Z6 @& W% F
IEC 61215:2005 Ed.2
. p1 f+ p% o# g, N: w2 X4 DSubclause(s):2 a; J; z! L' @: Y! ^0 y- m
10.15.2.a)" F5 ~0 b" x9 @0 h
No. Year
, v/ r9 v0 k. ~0 uDSH: s' q1 E! N' Y5 o& H# C* l2 @
0757
0 \( I1 F( \/ C: t/ ?! |2010( D9 k7 X, L9 r4 U- d$ Y- n/ k
Category:
; H' n* g8 s8 w/ L6 vPV$ a/ ~( D5 l, X5 X; L
Developed by:
q" s% _3 v$ Y2 gETF 9: o" S( v6 k1 ?+ f3 i6 ?
Subject:3 ]" p; b/ Q+ [% I0 U
Surface tension' P4 x* E3 B, d' `
requirement for wet
6 q& y7 O6 q4 P' @- X! Aleakage current test
, s( W0 B) y5 O0 Y" S0 PKey words:3 W" Q, x4 v w* i' }
Surface tension, Wet, l+ R5 u# |- E% g, o- E
Leakage Current Test
# x5 K1 m! J* b6 E1 k, JApproved at the 2010
2 z1 J7 u( n! f9 ]( K% ~5 Y$ ZCTL Plenary Meeting3 s% d4 O, ?+ I
Question:
* s9 O$ e' D1 _7 T7 l0 aIEC 61215:2005 Ed.2, Clause10.15.2.a) requires certain surface tension of the water
1 p' Y0 @- z% Z8 \" afor the wet leakage current test, however, the newer standard IEC 61646:2008 Ed.2
' u5 R. T8 v% W0 r _Clause 10.15.2.a) does not. The water surface tension measurement was required
0 z6 n( e% p( G3 O" @! qalso in the IEC 61646 Ed.1, but this requirement was deleted in the second edition.
7 v" p6 A4 G4 a( hThe WG2 of TC82 has made the same decision for the upcoming IEC 61215 Ed.3
+ L4 `- L6 E% J1 Xstandard. This standard, however, is not due to be released until 2010 or later. It is,
! R9 K3 G% t: K/ O4 Utherefore, suggested to resolve this discrepancy by this decision sheet.$ J! l/ R6 i% _; r5 ^9 `* ~& F
Decision:
4 _0 N! x4 [( Y _- O2 sInstead of IEC 61215:2005 Ed.2 Clause 10.15.2.a) use IEC 61646:2008 Ed.2 Clause
+ M1 b7 t5 U9 D10.15.2.a)
3 p) V( F6 l0 @# p
( V' H5 M. ~3 ]: ^6 H/ q! V o! S' X# ~# {
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|