|
| DSH 757
4 x/ t+ T( z# D7 K7 N
: ~9 C/ X$ A, {2 u1 @5 M | Surface tension requirement for wet leakage current test9 `+ d; b# G# K) I1 Q( N& J( r1 n
| 10.15.2.a)6 ?8 k$ w- }. ~, L9 s! u7 u
| 61215(ed.2)) z' R9 z" q( t' {3 ~+ Z4 z0 r
| 7 E+ o. t8 R+ j3 b
Standard(s)- (incl. year)
) X6 J$ G1 `; u% b! H( i1 i8 kIEC 61215:2005 Ed.2- G. u& A# h% ~/ E9 I; C
Subclause(s):4 x, }5 Z- V+ S4 t( o
10.15.2.a)
# ?! h0 m. t$ G" x0 [, U& [No. Year
0 b( f: c$ C9 z' ~DSH
7 A& G& ^ K. f& L( U8 W7 o07571 i) q# M h Q" W ]
2010
2 f) ~9 O; x8 UCategory:
7 v6 t+ |+ L8 l0 L# J* V1 ?. m# SPV U& w5 S+ b0 ^% f* e5 K
Developed by:' [+ N+ E) w- J' ]- R8 Q
ETF 9; J3 Q+ S- z+ V3 h; R( a
Subject:
: Z6 P) V% x3 \* ZSurface tension- N5 K4 K5 E) a
requirement for wet8 ` ?9 i. k. L7 o3 z7 C$ ]: w
leakage current test
! z; m) f( [5 E8 `8 ]Key words:- U+ q4 p6 [0 L6 l6 S3 D8 F
Surface tension, Wet- q5 j( ~* R! o. d
Leakage Current Test
0 L/ W6 {# S( V; |5 _! ]9 `Approved at the 20107 Q+ d9 D( z7 B0 j6 |8 u6 @
CTL Plenary Meeting! j5 p- u+ _4 ]% b# T6 Z
Question:9 ]+ L& C" B* W+ P+ m U
IEC 61215:2005 Ed.2, Clause10.15.2.a) requires certain surface tension of the water
, x2 W. c' @. L5 ?( Y: C* |" Jfor the wet leakage current test, however, the newer standard IEC 61646:2008 Ed.2; a5 D- j+ r( |
Clause 10.15.2.a) does not. The water surface tension measurement was required
, A6 b0 w# g, Y8 T6 Q4 R* V' [also in the IEC 61646 Ed.1, but this requirement was deleted in the second edition.
e$ |0 A/ e' V) ^9 [5 V, RThe WG2 of TC82 has made the same decision for the upcoming IEC 61215 Ed.3
. r7 [9 h% U: ~standard. This standard, however, is not due to be released until 2010 or later. It is,4 Y: f/ P" c* s: N4 ?
therefore, suggested to resolve this discrepancy by this decision sheet.
# ?3 a% u2 D% qDecision:* g7 n5 Z) U3 S0 F% p
Instead of IEC 61215:2005 Ed.2 Clause 10.15.2.a) use IEC 61646:2008 Ed.2 Clause4 M7 i- r/ e* ?3 b
10.15.2.a)
& r+ g [( p, D3 R. L9 F( ^+ ~
' l. C$ H4 L+ x, I g
2 V2 q/ A% a& ^: c2 d6 C |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|