PDSH 005/07 Luminaires provided with LEDs

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

PDSH 005/07 ! M) P2 ^/ w; f- d! g& ]

Luminaires provided with LEDs $ @0 M. C" w' G

General Section 12 % m& A+ k4 ^% q! r/ |

60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-13(ed.1) & 60825-1(ed.1) & EN 60825-1:1994

5 y5 ^' I4 c0 B- I1 cStandard: IEC/EN 60598-1
IEC/EN 60598-2-6
0 E5 T3 d5 X  T8 q& \  U2 JIEC/EN 61347-2-11
. u+ r) k0 ]) BIEC/EN 61347-2-13
: U$ H3 r4 g: p% ?% H- n- GIEC 60825-1/1993 (§)
EN 60825-1/1994 (#)
Sub clause: General
Section 12
Sheet N°: 005/07
Page: 1(1)
. h; x  ?$ a. t4 c8 d2 FSubject: Luminaires provided with LEDs
Key words:
8 M  X! T  K. Z" S: w' c# F2 G- Control gears
- Section 12
$ {$ R2 [* x$ s8 @; G% z0 P& D- IEC/EN 60825-1 (§) -
4 E. W  X+ ]# R6 K5 H1 i8 G) q(#)
- g  F3 q* j5 Q- |' I- uMeeting:
. P, R9 l" V) K5 e' [% LTo be approved at
CTL 45th meeting
" J6 L" X7 T# |3 VQuestion: Is it possible to approve luminaires provided with LEDs?
; \. R. U6 |- o+ WDecision: Yes, provided that:
" R2 X9 S& M* s) [" E2 \; G5 }1 U- the LED circuit shall be verified according to IEC/EN 61347-2-13 or IEC/EN
2 b5 l. }9 N6 `+ I% `, F2 K" D61347-2-11 (*) and the LED shall be tested according to IEC/EN 60825 –1
(Safety of laser products) (§)-(#), if it has laser radiation in the wavelength
0 A* H: [1 _7 }0 o: s6 Hranging from 180 nm to 1 mm. Only LEDs classified as Class 1 lasers can be
9 }: M% k" a: j' uused without problems for lighting purposes without protection.
- The thermal tests required in Section 12 of IEC/EN 60598-1 shall be carried
/ f# V- W; O7 v- ^" dout as follows:
) E0 H0 W7 g7 l% ha) Luminaires (Class I or II) with built-in control gear shall be tested
according to the requirements of IEC/EN 60598-2-6.
2 W8 M9 I* {* \/ r( L, B& l1 j% Jb) For Class III luminaires the manufacturer shall provide the necessary
information to power up the LED circuit correctly in the instruction sheet.
Alternatively, the manufacturer shall inform Testing Station about the
8 ~! {& V, W+ Itrade mark, the type and the technical characteristics of the appropriate
9 V9 C( L6 {; @$ j  s9 vcontrol gear to be used. There are three different control gears namely, the
. C; _9 p3 m1 W% `0 p) stype and the trade mark as indicated by the luminaire manufacturer; an
( T$ X5 Y, q; F2 Q! b9 `electronic control gear clearly specified in the luminaire instruction sheet
! t( j: |+ \" e$ Y# |1 Cand a ferromagnetic control gear. The tests shall be carried out as required
% m  ?% m6 J0 ?) k& r5 rin Section 12 according to IEC/EN 60598-2-6 with the appropriate control
gear.
  j0 p* K) U: W$ ]1 |7 m0 `: T(*) When IEC/EN 62031 (34A/1168/CDV) will be published, it will takes
) D: W6 R% d" E, [1 F. M8 u4 Hover IEC/EN 61347-2-11.
(§) + A1/1997 + A2/2001
: ~7 d0 l% n! B7 d5 C3 C3 P$ u; i6 ~7 e(#) + A1/2002 + A2/2001
5 I$ b2 O/ `1 p/ t4 EExplanatory notes: The matter is under discussion in Lumex/Comex; we will wait
# `4 v- C1 J: [for the relevant outcome.


  q  K1 ~. P7 ]" J3 X