PDSH 005/07 Luminaires provided with LEDs

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

PDSH 005/07 8 c' g  ]# M6 W1 A

Luminaires provided with LEDs

General Section 12

60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-13(ed.1) & 60825-1(ed.1) & EN 60825-1:1994

Standard: IEC/EN 60598-1
0 P3 u- q4 {/ J) j4 h9 EIEC/EN 60598-2-6
+ u* l8 g% q5 D8 v/ ~0 XIEC/EN 61347-2-11
" A- j* f7 E) Z. V* \2 t' d/ zIEC/EN 61347-2-13
* A/ e, o! ?* ~IEC 60825-1/1993 (§)
EN 60825-1/1994 (#)
Sub clause: General
' b/ E6 i2 a9 J0 jSection 12
2 s/ k: L* V3 S, m7 r0 gSheet N°: 005/07
  A& ?) g9 z( z: K- CPage: 1(1)
Subject: Luminaires provided with LEDs
Key words:
2 h# s5 Z9 A5 J8 g4 t- Control gears
- Section 12
) X, @1 f- O5 s- IEC/EN 60825-1 (§) -
9 P. k' X' g' r(#)
Meeting:
" u1 r8 p4 J3 m- ~3 C) c) vTo be approved at
4 ^& t" I% L3 fCTL 45th meeting
1 u- U$ X9 ?, W  j6 z* cQuestion: Is it possible to approve luminaires provided with LEDs?
Decision: Yes, provided that:
- the LED circuit shall be verified according to IEC/EN 61347-2-13 or IEC/EN
2 @6 Q* H, [9 V! o8 _61347-2-11 (*) and the LED shall be tested according to IEC/EN 60825 –1
(Safety of laser products) (§)-(#), if it has laser radiation in the wavelength
ranging from 180 nm to 1 mm. Only LEDs classified as Class 1 lasers can be
used without problems for lighting purposes without protection.
! B; d3 @1 s9 s/ U9 a- The thermal tests required in Section 12 of IEC/EN 60598-1 shall be carried
: N0 p" _$ w" M/ nout as follows:
6 b1 _- u2 m& ga) Luminaires (Class I or II) with built-in control gear shall be tested
3 Q7 C! D$ S# z3 o6 D5 Faccording to the requirements of IEC/EN 60598-2-6.
1 h4 w: F$ a0 v! tb) For Class III luminaires the manufacturer shall provide the necessary
information to power up the LED circuit correctly in the instruction sheet.
/ g5 F! ^0 @3 a, H9 k& d6 A9 tAlternatively, the manufacturer shall inform Testing Station about the
; G: h$ Y4 ^$ j8 o: Z0 w+ O5 Atrade mark, the type and the technical characteristics of the appropriate
5 Y- h! N2 `( v$ Bcontrol gear to be used. There are three different control gears namely, the
6 m3 ?  {9 s/ w3 O( }type and the trade mark as indicated by the luminaire manufacturer; an
electronic control gear clearly specified in the luminaire instruction sheet
9 M. m! ^( T, X4 Sand a ferromagnetic control gear. The tests shall be carried out as required
in Section 12 according to IEC/EN 60598-2-6 with the appropriate control
gear.
0 {6 `4 e1 U' O(*) When IEC/EN 62031 (34A/1168/CDV) will be published, it will takes
over IEC/EN 61347-2-11.
(§) + A1/1997 + A2/2001
(#) + A1/2002 + A2/2001
Explanatory notes: The matter is under discussion in Lumex/Comex; we will wait
for the relevant outcome.
" z" m: u" h+ }6 E0 V! ?
1 s- U0 c/ c* z( C% M! U. n" f. W
% {9 ]+ G4 j  c, M  {! h5 \; C

qsin

小编同志，除了CTL决议之外，能不能把其他类似OSM，EK1等等决议也汇编下！！！！