|
; g" I* G! Q5 A& z
: l& H B, ]4 ?8 J( D0 X5 z A | Separation of Internal Circuits
+ t9 \& T$ ]& g1 |* C" d | 6.6.1
5 @8 r( r m7 r) ?: M4 k9 K | 61010-1(ed.1);am1;am2
! T, p& Q( y' ]: j/ |9 | |
& h% ~ F% \4 m$ o1 b4 ~% S0 K( ^5 y; z
Standard:
R: ?7 K% w: R+ H8 ^IEC 61010-1:1990 +A1:1992 + A2
/ |( b! N, b; N' J' M2 N:1995
- O+ \8 T* C$ X$ P5 b* ?9 hSub clause:
/ B0 E1 D! n/ S6.6.1. n1 O8 T6 y4 d- A3 G: @( N, C
Sheet n. 3338 U8 k# V4 j L1 s+ |
Page 1(1)
; |+ w2 p5 ?8 r0 e4 t8 _Subject:
# g7 W- u Y0 d% K6 aSeparation of Internal circuits' }6 ~+ ?$ q0 ^: F# P- i
Key words:2 X3 l: x8 h9 F* K6 G. ^0 _
- Isolation system! F$ w- p p1 ^$ w: i2 D
- Materials Declaration
6 H1 ~6 r% ?# o' H- ~6 YDecision n. 23 taken at
- M' u7 x, s( D+ A$ q8 X7 }. ?! k37th meeting/2000) H6 g8 w: q; C' W: C3 ^4 R: E
Question:" ~* b# ?. x% I
What should be the criteria for accepting a manufacturer’s declaration for
. u8 }- l, z4 `$ l9 @isolation systems and materials?7 U, s, {5 S8 Y3 J$ U
This question is from CTL.
# f+ y' p6 Z" f7 `8 d9 _+ J: t- HDecision:
. N5 G% N! j" ]! b' v6 S) lIt was agreed that although manufacturer 's declaration may well be taken into consideration,
' w% ^( n I( [' nhowever testing must be performed to ensure that requirements of IEC61010-1 is met.% T% L1 z+ _5 k( Q9 C+ N( L
Explanatory Notes: H' y' O4 P* i, t6 A
In IEC61010-1, there is no requirement to simulate the ageing process of critical components
- z3 [/ ~5 W( \* `3 Q- esuch as the mains / isolating transformers.
' g5 q" R! S y3 c3 k# zIt should be noted that after each single fault condition test, where necessary, the required" \, Q& s) u: p8 i5 k6 l
high voltage test must also be applied to ensure that at least basic insulation exists.) ^! h) i- c( S4 o/ u7 w# V% T
Note that under compliance criteria there is no reference to 'Declaration by manufacturer'.6 l1 b# W, M/ {. ]+ ]
/ p7 t$ b8 v8 B: q n) m- r: d
! I9 v/ m" C" f' M& q; `) P5 R6 ]3 q: u% i4 ?/ U0 l2 V
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|