UL1993 对于PCB的间隙要求

jsspace

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

UL1993对于PCB的间隙没有要求，满足耐压测试即可？

zhangtaooo

UL 1993
! D8 E: R4 h+ `; b0 eA ballast for high-intensity discharge lamps shall comply with the
requirements of UL 1029 and UL 935.
* x7 }$ j. g2 T" j6.4.2 A ballast not previously investigated as described in Clause 6.4.1 shall be evaluated in the device.
The construction requirements of UL 935 or CSA C22.2 No. 74 or NOM-058-SCFI shall apply. See the
% e! U9 Z+ S( \0 i9 ^* |appropriate standard for details on coil insulation materials, thermal and overcurrent protective
, e% l8 ?/ E6 C, ucomponents, printed wiring boards, and spacing of electrical parts on the printed wiring board.

clause 6.6 and table 6.1.

' [  K" g" P1 b7 z9 d/ u, Land LED lamp for ul 8750  clause 7.7 and table 7.4。

% A4 i( u' l+ G1 ]+ P* G

jsspace

hzj101988 发表于 2013-5-23 17:27
. [; r3 _2 y, K8 h& ^& g: o8 u这个是哪个标准的啊

服了你，这个也被你翻出来了
5 J, h' N9 e% a9 lLED灯泡的PCB没有距离要求，满足耐压即可

hzj101988

babyliss 发表于 2011-6-16 14:49
有呀
, b- r0 y- O0 [$ Gin primary circuits,1.5mm minimum spacing are maintained through air and 3.0mm minimum spacing  ...

这个是哪个标准的啊

shideyuan

有要求，电气间隙，和爬电距离都有要求，不只是满足耐压

jsspace

引用第1楼babyliss于2011-06-16 14:49发表的  :
有呀
( J& ^$ Y, j$ P* Din primary circuits,1.5mm minimum spacing are maintained through air and 3.0mm minimum spacing are maintained over surfaces between the current-acrrying parts of opposite polarity on PCB of power unit.And 1.2mm minimum spacing are maintained through air and over surfaces of insulating material between current-carrying parts of opposite polarity and between such current-acrrying parts and dead-metal prats or low voltage isolated circuits.

是啊，我就觉得奇怪啊，我是在以份培训资料里看到说满足耐压就可以了

babyliss

有呀
in primary circuits,1.5mm minimum spacing are maintained through air and 3.0mm minimum spacing are maintained over surfaces between the current-acrrying parts of opposite polarity on PCB of power unit.And 1.2mm minimum spacing are maintained through air and over surfaces of insulating material between current-carrying parts of opposite polarity and between such current-acrrying parts and dead-metal prats or low voltage isolated circuits.