|
APPROVAL CERTIFICATE NUMBERING SYSTEM
* G. E4 a% ^& }& @1. The number shall consist of five sections separated by the ‘*’ character.7 {! L9 c. J% r/ r
Section 1: the lower case letter ‘e’ followed by the distinguishing letter
9 y2 \0 L+ l b: _(s) or number of the Member State issuing the approval:
1 {+ I( E( W ?4 r% c4 h( ^ F8 y7 @# \! Z% \- I
1 for Germany
. @5 E! u" S" t* J( e. B ]3 u( d" B" _2 for France5 E) k. ]) J6 h, Y
3 for Italy
& t* S3 u; T$ X$ ^4 for the Netherlands
2 |4 U; m7 W+ i/ g5 for Sweden
/ t$ W2 F0 I( e* Y* c- E9 m2 H6 for Belgium2 v2 f# m0 |4 H
7 for Hungary
' f: B- O- c A) Z9 p: a8 for the Czech Republic) O" e' t4 c& m. ]# X
9 for Spain
+ J3 d$ m2 J0 o/ k11 for the United Kingdom
; ~1 ?0 R) b, ^0 ^" g4 f' g/ V3 {- b12 for Austria
3 W; n- _: }1 F) i" I13 for Luxembourg
t5 D- O5 \3 l: v- \* y8 Y17 for Finland
. {) [7 R/ Z; }* W18 for Denmark8 G: W: w7 z# i8 f% L% \1 F
19 for Romania
( v7 o' m7 L2 \: ?& E20 for Poland/ C+ W- s2 \- M) X
21 for Portugal
. B6 C2 q4 B1 e9 i9 ~23 for Greece
. l; {4 V; u# b; v$ U$ Z- s24 for Ireland
' y0 O* R3 g7 V9 h& U' b26 for Slovenia8 E3 x6 U6 t4 J2 Z% \9 F6 L
27 for Slovakia
' V4 V' `( J1 D+ N" u29 for Estonia
0 i& W% X8 r, j) y6 ~+ ]0 S32 for Latvia$ C2 ~* A3 B: A5 q/ K$ I' H
34 for Bulgaria
& C! \, F0 w5 e6 g36 for Lithuania6 c) r0 O* m/ [
CY for Cyprus
! r" ]0 W/ H$ ?+ `' u, yMT for Malta
4 Y) Q% a0 d, \% jSection 2: the number of this Directive. As it contains different implementation& H% [4 Z) y' c$ \# s& t" _
dates and different technical standards, two alphabetical/ H$ S5 v/ a5 e! J L w9 e# i' {" M
characters are added. These characters refer to the
7 W) I: n( i8 b8 n) s2 |% x A, {different application dates for the stages of severity and to
6 A+ r8 Y* Y& R" b1 cthe application of the engine for different specification of% p" U0 x% n7 u5 A
mobile machinery, on the basis of which type-approval was9 }1 D$ m& m! I0 ~- L
granted. The first character is defined in Article 9. The
7 d; Y# P' A1 @6 `second character is defined in Annex I, section 1 with
3 g v1 H* E' z) tregard to the test mode defined in Annex III, section 3.6.
, q Z8 d* A& g* r0 U$ i4 h: MSection 3: the number of the latest amending Directive applicable to the
! l; J3 k/ x& O0 W7 o: iapproval. If applicable two further alphabetical characters are2 `/ `3 z( C/ Y7 t) |
to be added depending on the conditions described in section
9 y! s, p. X+ ~* }2, even if as a result of the new parameters only one of the; G, a, a; l. H9 {) z
characters was to be changed. If no change of these characters
6 [9 {, b' ?+ @0 J( s, X4 ]apply they shall be omitted.
8 L$ _- ~& H* S7 USection 4: a four-digit sequential number (with leading zeros as) i- R/ x) w2 X. y
applicable) to denote the base approval number. The
9 P. d) l1 l6 jsequence shall start from 0001.
6 L: S) b H; M6 B. lSection 5: a two-digit sequential number (with a leading zero if
; j5 x3 P* j9 D- C+ x3 F! Z& Uapplicable) to denote the extension. The sequence shall
1 r# J$ Y8 F6 L8 f; ]6 P& X, fstart from 01 for each base approval number.. L: @9 N6 w. k8 W$ k
2. Example for the third approval (with, as yet, no extension) corresponding to1 M% b" r/ S% h* g
application date A (stage I, upper powerband) and to the application of the
, x2 D- O: ]: @. I8 Qengine for specification A of mobile machinery, issued by the United5 p5 b) \: |! |- z
Kingdom:/ s. F& C5 t: j4 b: n4 P. g
e 11*98/…AA*00/000XX*0003*001 X* {( h/ x0 t) {
3. Example of the second extension to the fourth approval corresponding to! P' V" F7 m/ t# y/ D
application date E (stage II, medium powerband) for the same specification
3 p+ N0 |' \! q# A: l/ l* S% ]of machinery (A), issued by Germany:) \" }( h9 ]2 q9 J
e 1*01/…EA*00/000XX*0004*02 |
|