逆变器中交流、直流侧的保险丝，必须要安装吗？

yeanling

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

看到其他厂家的一些逆变器产品中都没有交流、直流侧保险丝。或者是只有交流侧有保险丝。那样的设计安规上是否可以？保险丝到底是否需要安装？怎么安装才符合要求呢？

11狼

大部分厂家都是在交流侧安保险丝，但是也有在直流侧安装的，这要看你的设计了

清水白菜

直流侧可有可无，通过short test评估就OK；
2 }: }: j8 n5 `交流侧就看你设计了，要样机里没有，需在说明书中说明装机时交流侧用的外置Fuse的Rating，相关要求如下（IEC 62109-1）：

% M1 R5 f) y1 T4.4.4.5 Output short circuit
Each power output port of the PCE, and each section of a tapped output, shall be tested one
0 C1 N- z5 b$ w: \( X7 B7 Y; Fat a time, to simulate short circuits in the load or wiring. Overcurrent protection devices as
6 L4 b# o3 O4 rprovided in the PCE or as specified in the installation instructions, shall be fitted during the
test. All other outputs are loaded or not loaded, whichever load condition of normal use is less
8 y  t% X/ [9 V" M2 ^; H- afavorable.
6 j: H, A, k! g" O# `/ \. a$ Z  KTesting is required to be performed on all combinations of terminals for the port under
4 D1 R5 M9 p# j' u4 \consideration, two at a time, including neutral and earth terminals, and one test with all
' j- n- V0 d3 X* D( ^current-carrying terminals of the port shorted together at once. Where analysis shows that the
test for one combination is representative of other combinations, tests may be omitted.
In addition to the requirements of 4.4.3, the short-circuit currents are to be recorded and if
they exceed the maximum rated current of the circuit, the maximum measured current shall be
provided in the installation manual for the purpose of coordination of overcurrent protection of
1 p. o$ G/ D! Y! }the external circuit conductors (see 5.3.2).
The value(s) to be recorded and to be provided with the PCE instructions are the peak
" b5 R+ |0 l( k% L; ?% V4 k7 ?current, and the highest of the RMS current values measured or calculated over a time period
as follows:
a) for AC signals, 3 cycles of the nominal AC frequency for the port under consideration, in
5 [) ?0 d1 y* f2 S1 zwhich case the value is to be stated as the 3-cycle RMS value;
6 y0 ^( {3 E" S: n1 t0 ^' D5 wb) for all signals, the duration of the short circuit from the time the short circuit is applied, until
the time the short circuit current is interrupted by a protective device or other mechanism, in
which case the value stated is to include the RMS value and the time period in seconds;
c) for short circuit tests that result in a continuous non-zero value, the steady-state RMS
% E( X: M9 T; [: L. Z% Mvalue, in which case the value is to be stated as a continuous RMS value.
$ o- U7 [9 e0 A, r$ A9 i$ ONOTE Where the intended use of the short-circuit current information requires a different type of measurement,
0 F+ i; H& x+ \  C* U: Fadditional data may be provided. For example, for AC mains fault current contribution some utilities may prefer a
, ^6 \3 N1 }  h¼-cycle RMS or other RMS calculation to the 3-cycle RMS above.

戏尘

和设计有关 然后看你做异常时FUSE 的能否保护

houfengp83

不管是交流侧或者直流侧都可以不用保险丝，交流并网侧可用继电器保护异常动作，直流侧如果连接到限流源就不存在过流

kevin245

沒錯 -->不管是交流侧或者直流侧都可以不用保险絲      
我們以前有裝, 現在都拿掉了.