家电设备需要做浪涌试验吗

herrylin

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

家用的电器设备需要做雷击浪涌试验吗，试验电压是否为1KV？

tianchi0305

有要做的，第19章里面有说到的

kk20082008

当然是要做，类似EMC的部分。

kamleung

If your product is AC operated, then Surge test is necessary in both the EMC standard (EN55014-2) and Safey (EN60335-1). Please note that the test levels and the PASS requriements are not the same in the EMC and Safety standards.
0 c6 ?3 y( O. O' E1 I# w
; E* Q0 K+ |8 N6 ~' m0 }For EMC, the test voltage is
    - Line to Line: 1kV
    - Line to Earth: 2kV
1 Q: z1 U: u# C$ B9 OThe product is switch ON before applying surge. The product is considered as PASS if it can keep on running after the surge has been applied.
& |7 U: a+ L$ {! @1 w3 W+ l. }
- Y5 u/ }3 e3 K* g+ eFor Safety, the test voltage is
    - Line to Line: 2kV
    - Line to Earth: 4kV
The product is switch OFF and the surge arresters is disconnected  before applying surge. The product is considered as PASS if it can keep idle or nothing hazard happens after the surge has been applied.

michael.king

这个是必须地

花儿

IEC 60335-1 clause 19.11.4, 对带有待机状态开关 或通过电子断开获得断开位置的开关的器具需要进行19.11.4.1-19.11.4.7的试验，其中19.11.4.4需要对器具电源接线端子进行电压浪涌测试！
( @! ^5 ]( K% T/ Y$ ]1 B* ]5 ^3 c
7 N4 T( ?& N& _% c+ |+ V9 ?5 @& P
19.11.4.4 The power supply terminals of the appliance are subjected to voltage surges in accordance with IEC 61000-4-5, five positive impulses and five negative impulses being applied at the selected points. Test level 3 is applicable for the line-to-line coupling mode, a generator having a source impedance of 2 Ω being used. Test level 4 is applicable for the line-to-earth coupling mode, a generator having a source impedance of 12 Ω being used. Earthed heating elements in class I appliances are disconnected during this test.

# H. h* u3 n( E, R8 t NOTE If a feedback system depends on inputs related to a disconnected heating element, an artificial network may be needed. For appliances having surge arresters incorporating spark gaps, the test is repeated at a level that is 95 % of the flashover voltage.

Andy.Yang

you must know, there are to surge tests for the products:
1. One is for safety requirements, to verify the insulation characteristics of the products, and sometimes it also can be called impulse tests;
2. The other is for EMC requirements, to monitor the impact of the lightning to the products.
7 b9 s: ^/ v5 ]3 s- X
& f$ A8 s$ S" PBut the basic waveform of the above two tests are similar.....

cylam128

需要滴。