|
| DSH 590" c2 X4 w) ~7 K. J6 V% u& m. p7 M
6 m9 F7 L% W/ ^$ D, W( {6 L | Rule for creepage across grooves and similar surface discontinuities
. j& j) d* D9 \1 {3 A3 L% |# N | IEC60664-1: 1992 cl. 4.2 IEC60335-1: 1991 Annex E IEC60335-1: 2001 Cl. 29 IEC60730-1: 1999 Annex B IEC60950: 1999 Annex F IEC60950-1: 2001 Annex F IEC60065: 2005 Annex E IEC61010-1: 2002 Annex C IEC60601-1: 1988 Notes Figs 39-47 IEC61558-1: 1988 Annex A IEC61058-1: 2000 Annex A IEC60598-1: 2003 - IEC60745-1: 2001 Annex A IEC61008-1: 2002 Annex B IEC60947-1: 2004 Annex G/ G" ~2 G- v8 J( W% C8 D) |' ^
| 60335-1(ed.4) & 61058-1(ed.3) & 60598-1(ed.6) & 61010-1(ed.2) & 60950-1(ed.1) & 60947-1(ed.4) & 61008-1(ed.2);am1 & 60065(ed.7);am1 & 60664-1(ed.1), l" J- l( i9 B. j
| ; k; q$ s4 _* V8 l' p) W, J
Standard: IEC 60664-1/1992
& G8 D% S) h- o/ X# P7 T. ~, G7 kIEC 60335-1/2001" i" H1 S& z1 a0 h% d8 A: q
IEC 61010-1/20020 M& S7 g; n% O& c5 c
IEC 61058-1/20004 {6 P" C9 j$ n4 J
IEC 61008-1/20026 H& b+ w' M8 _4 H, M; m
IEC 60947-1/2004
: O0 _" x: d5 _7 _* }, E- P# `IEC 60598-1/2003
3 u3 } `( ]1 W8 oIEC 60065/2005# x: O' t3 ^7 K, }1 Z6 m
IEC 60950-1/2001! a- x, b% p/ _3 Y* b
Sub clause:3 @ @( x* U& B7 o6 U
See Table below
# R% J1 g- u3 R- u* k7 k5 HDSH N°: 590
% }7 h% S6 Q) _Page: 1(1)
7 O% W3 ^7 P$ h( W6 z$ a8 t% GSubject: Rule for creepage across# T+ f1 _: \7 p8 I. q
grooves and similar
! `0 u7 n1 C) {% W& xsurface discontinuities
" g9 d$ J y& U0 A( [: K3 mKey words:( ?% Y+ g& i7 n* m) d
- Creepage
) H" b8 O* N4 }2 A# J' J K* R- Grooves. }0 X8 i' M5 l4 S
- Conducting path$ Z" d B$ ]4 S
- Shortest distance6 }5 b9 c7 z" [; T9 U! ~
- Through air
( {: L( X9 K6 g& T ~, R8 s+ zDecision approved
5 s- s/ c( F# |6 {5 T! uby the CTL during
# X+ I& q% F" Q& B9 X9 E7 n" I, Oits 43rd meeting in
+ a; r M4 F+ P/ DJohannesburg
0 w- d# A- Z9 C9 c1 [ g4 \9 YQuestion: As can be seen from examples 2 and 6 of IEC 60664-1 sub clause 4.2 corners
: | P3 b2 F; A& _0 l; Awith angles greater or equal than 90 degrees are not bridged. IEC 60664-1 does
+ N l; U) k) Z( X1 u9 N( ^/ Lnot contain specific information at which angle less than 90 degrees bridging
) K5 O+ g0 X/ Q' x. H) d- ]* sshall be applied. Some of the above mentioned standards specify that bridging* O( f7 N, o& [1 s9 ~9 ?
shall be applied for angles less than 80 degrees.3 N: |0 d! u3 [9 M* M
Can this 80 degree rule be applied in general for all standards?
. I+ A9 k, i0 Q4 j0 yDecision: Yes. The 80 degree rule shall be applied in general for all standards.1 ?, b2 F- n7 R) V- u
) A# ~/ Q5 r1 }7 z2 V% b5 @' J, d
& @ T K& K, b# e |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|