|
|
Tensile Stress, brk, Type I, 抗張強度5 X8 E: }- y3 n* Z4 K; S
Tensile Strain, brk, Type I, 拉伸變形
! G+ p1 \- d( vFlexural Modulus, 彎曲模量: B# F& K" m2 ~; x# {
Hardness, Shore A, 硬度(肖氏)0 G% {( a: m2 N
Tensile Stress, break, 抗張強度
; p+ A. q$ v- TTensile Strain, break, 拉伸變形
, Y+ J0 O5 j7 Z8 T iFlexural Modulus, 彎曲模量
6 A2 _- }5 k% H9 w2 }' ?! vIMPACT4 i5 i2 s: C& q1 H1 w5 W, Q$ |3 O
Brittleness Temperature 脆裂溫度3 G* M8 U; u- @# j9 ?. d! _
PHYSICAL4 u9 \% T# L$ c& d8 b' Z! I: |
Specific Gravity 比重
# `8 J" x S1 N1 p! y, |4 uMelt Flow Rate, 熔融指數( S4 C2 ~6 W0 Y5 w' L- O- h/ M
ELECTRICAL
( W$ s* T: i7 J' E* gVolume Resistivity 體積電阻
# h0 a0 ]7 r% H$ R: w' @$ G. y5 p) q& URelative Permittivity, 介電常數
+ ^4 F7 ~7 C C3 h) b2 F! fDissipation Factor, 損耗角) m3 m/ V) B, @* G/ B$ E
Dielectric strength in oil, 油中介電強度5 E+ T( T& Z" `" K) Q |! R
Comparative Tracking Index 比較留痕指數(CTI)
& K' T; y" f2 {$ X! P& a7 jFLAME CHARACTERISTICS
( W, G' j. r; P) {, C& ^Smoke Density on 0.5mm plaque, Non-flame, Ds, 無焰式煙密度
2 E7 X# l8 B0 G. b3 M& S; qSmoke Density on 0.5mm plaque, Flame, Ds, 有焰式煙密度
1 K+ Z! s0 l/ {0 w+ xGlow Wire Flammability Index 960°C, passes at 3 mm 灼絲燃燒指數
1 _1 @' ?1 ?# d. _6 |Glow Wire Ignitability Temperature, 3.0 mm 800 °C 灼絲引燃溫度; L8 G$ v7 x9 T( O/ H
Oxygen Index (LOI) 氧指數
3 l% q0 L# z3 X! n EWIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper" |% z2 } ]5 O1 A4 R K; T9 t
Tensile strength @ break 抗張強度
5 m. Q5 A/ H- XWIRE AND CABLE - UL 1581 tested on 2.0mm wire with 0.12mmx20 stranded copper
, [0 |4 [" l& y& U. N" sTensile elongation @ break 伸長率4 B3 H) h4 t5 {: R0 E
Tensile strength @ break after 7days @113°C 化後抗張/ l; y' h; g; f* J' ^) C2 F/ z
Tensile elongation @ break after 7days @113°C 化後伸長
& P2 Y1 p2 O8 J& J* ], nUL temperature rating 80 °C UL 額定溫度
6 E9 F1 J j t! r6 e5 `# aHeat Deformation at 100°C/250g 加熱變形9 H3 z: ^/ j* W, i5 y( j
VW-1 Pass - UL 1581% Q y5 M* g( P ?% w+ p$ Z
! j5 x9 V8 P/ E- ~ ]) U2 u" EDrying Temperature 干燥溫度3 p8 N+ T4 n: k; ~$ y+ B
Drying Time 5 - 7 hrs干燥時間
# ?$ a$ U/ i/ o7 Y' q2 T( EDrying Time (Cumulative) 12 hrs干燥時間# u: r1 T" a! ~( d
Maximum Moisture Content 0.02 %最大濕度含量/ | B% i Y5 c) T
Extruder Length/Diameter Ratio (L/D) 22:1 to 26:1 -押出長徑比
4 c" E( Z: U- j, A6 ?Screw Speed 15 - 85 rpm螺杆轉速
) r& @0 F3 @$ k' m- E7 t8 j) Q2 DFeed Zone Temperature 180 - 230 °C輸料段溫度, K% V* U2 M3 u4 c
Middle Zone Temperatures 230 - 260 °C中段溫度/ u& {2 f2 {: y% U
Head Zone Temperature 230 - 260 °C頭部溫度
! V0 I# [ {) O4 @/ S, {Neck Temperature 230 - 260 °C機頸溫度+ x; ?8 p, R( Z9 D, p% n! J0 `
Cross-head Temperature 230 - 260 °C機頭溫度
9 p3 O# @3 I3 LDie Temperature 230 - 260 °C眼模溫度9 S8 n2 ^7 y- u
Melt Temperature 230 - 260 °C熔融段溫度
; q) e# Y4 U$ g% {; @" ]5 jConductor Pre-heat Temperature 25 - 120 °C導體預熱溫度+ {$ M( i* K, f# a g
Screen Pack 150 - 100 -網目8 y: C) N& {, ^* ~1 c
Cooling Water Air Gap 100 - 200 mm冷卻水間距
2 n" W0 h' m* x3 R4 ?4 L1 lWater Bath Temperature水浴溫度 |
|
/1 
|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网
( 粤ICP13023453-10 ) 
窥视卡
雷达卡
发表于 2009-7-24 21:02
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
抢沙发
千斤顶
显身卡