|
4 L9 t3 G- _; ~# n% }" M, P& ?Standard- No. Year
/ A$ P+ x- Q9 {- DIEC 60950-1:2005 DSH" ~5 q" B I# @
0700 @& n3 a$ K3 q# N& w$ M& Y
2008" u" c5 Y1 ~, g7 |- e" F
Category: OFF
, N+ Q1 l, C. x: \" e" ^1 p8 eSubclause:
4 P+ O( w r- k/ }* {, l4.3.54 G* F0 ]. P5 `1 p9 V
Developed by: ETF 2
6 B2 Q# h' O! v6 ySubject:
, {; C T2 k3 B. s! kPush force for connectors; K- V0 z! J2 X3 q$ P1 y0 j+ ^
Key words:
& `, \! u( Q7 a, z& k7 F-Travel adapter;; ], T7 J. ~; y1 q; H; |) A1 r- L, L( |0 v
- connector misconnection
% m% G( K0 s: {$ v$ h+ k( sDecision approved at the
( B/ d! S; X5 g46th CTL Plenary Meeting+ s8 }4 ^/ F( @+ t" j. u
in 20091 k. u9 V8 e" B) D8 q& B6 J, @; W
Question:7 T7 H2 S) J' r4 k2 `
A travel adapter consists of two separable parts:
1 {0 {- e% b3 D% |' G/ Q· AC/DC unit (down transformation of voltage, safety separation provided)1 v8 Q: N! b, S6 I; R, ~+ }
· DC/DC unit with output cable (supply stabilization and voltage adjustment, no safety separation; n2 b2 ]) `+ {, i4 ^- O4 k# f: i
provided)
5 y1 U0 l5 b1 v; W( wThe unit can be used at AC mains (both units connected together) or DC (units separated, only DC/DC( z. b' Z6 t$ x, ^ [7 t. ]$ L
used). The AC/DC unit has a (Class II) IEC 60320-1 type appliance inlet; the DC/DC unit uses a6 ?6 w+ O, u" E& y
special 2-pins input connector.! x8 b ]. ^$ Q# ~
With a small force applied (less than 30 N) an IEC 60320-1 coupler can be inserted into the input
! r% O2 t' d1 _6 Z2 b0 oconnector of the DC/DC unit and make contact.
3 h' ?4 g6 P, E9 k; W! na. Is such design acceptable if a warning label is provided on the DC/DC unit and additional remarks
2 p& X) k, G+ Bare provided in the user manual that state that the connector of the AC power cord shall not be
s- Q( X- F& Jpushed into the input connector of the DC/DC unit?
. T" i4 w: r# T' m' }b. How much force must be applied during the testing of the input connector (DC) and appliance: d& H. {4 J7 N7 M
coupler (AC)?
. f2 F: Y8 J$ h) k6 V p( aDecision:
2 F' w# ?5 j, G8 G. n6 wA test force of 60 N (as specified in IEC 60320-1, no safety factor considered) shall be applied when8 s# e P% L# f% {
testing possible misconnection of IEC 60320 and similar connectors.
$ B# Q' i, y# x$ |( _8 a1 _( S
7 U7 ~' _ U9 b3 W2 C5 z/ R6 m& H7 {
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册安规
x
|