|
|
|  PDSH 005/074 u6 ]" e! Z& g$ p( v, ], [
' d7 i3 Q1 r4 T1 r# C | Luminaires provided with LEDs
# }9 D! l0 v0 x6 O3 m | General Section 12* D& W' g* C- N1 s: O; g9 I" ?
| 60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-13(ed.1) & 60825-1(ed.1) & EN 60825-1:1994
* b- d) g' T' p# [& n( |. M1 a: [, d' ] |
, N2 L" l; \# V5 z" ^9 o2 WStandard: IEC/EN 60598-1
' _0 W2 I% y% s! t& [& {3 hIEC/EN 60598-2-6
- o2 u/ U. f. q0 o) Y4 fIEC/EN 61347-2-11
# N6 R0 L' e8 X" k% L% N6 N$ KIEC/EN 61347-2-13
: J3 @, i2 o5 l# Y* EIEC 60825-1/1993 (§)
) [" \/ L7 G4 l, Y1 U$ xEN 60825-1/1994 (#)
& F9 A. v3 a2 q+ [$ ?5 P! dSub clause: General/ h; x0 M+ J8 b) A" E
Section 12
# ]( @2 R0 ~5 eSheet N°: 005/07
& R' i$ q2 e5 BPage: 1(1)
* J- I. `1 B6 s. o7 sSubject: Luminaires provided with LEDs5 [. M+ l" K( C, T; ^
Key words:0 m# m1 z; O& K Y6 S3 g3 K
- Control gears
! E# t- o Z% U9 ?- o8 A- Section 12
* `5 J! }% b' H, i8 v9 B6 }& q- IEC/EN 60825-1 (§) -
! S( i5 [" }- u t1 i(#)6 `9 |% ?4 x9 P, i# }
Meeting:, j' Q: u1 h# L' s; B+ Z! W
To be approved at
( W& |4 x4 D$ U* P) g+ KCTL 45th meeting6 I- l: q) n' b$ R; }! J
Question: Is it possible to approve luminaires provided with LEDs?
! h D3 d* L# qDecision: Yes, provided that:
9 ]: Z' g {3 I9 Z( D$ D$ l- the LED circuit shall be verified according to IEC/EN 61347-2-13 or IEC/EN
/ E1 C, u1 ]/ A2 m# R% C5 f61347-2-11 (*) and the LED shall be tested according to IEC/EN 60825 –1$ ~5 Q/ c E) K! T
(Safety of laser products) (§)-(#), if it has laser radiation in the wavelength8 q! [& K8 p1 x' D$ p
ranging from 180 nm to 1 mm. Only LEDs classified as Class 1 lasers can be- ?6 }' h# V1 c5 ~& {8 Q: q; A3 _
used without problems for lighting purposes without protection.
- s5 _9 C$ p8 V0 ]7 e! R- The thermal tests required in Section 12 of IEC/EN 60598-1 shall be carried# {. S! {7 t9 A1 {3 l7 ]
out as follows:
1 A2 E& z0 d' x* T3 ba) Luminaires (Class I or II) with built-in control gear shall be tested
8 {, E, V0 X s" aaccording to the requirements of IEC/EN 60598-2-6.5 y" F4 } @% [/ q; s0 H
b) For Class III luminaires the manufacturer shall provide the necessary4 V D& a0 `& P( q
information to power up the LED circuit correctly in the instruction sheet.
. [: ?6 E' l& x) h+ J8 J; MAlternatively, the manufacturer shall inform Testing Station about the1 ^* t9 [; c/ }( B- ?, t
trade mark, the type and the technical characteristics of the appropriate
1 ]/ @, u) y2 _8 l: S% ]control gear to be used. There are three different control gears namely, the
6 G+ J7 d9 t+ Qtype and the trade mark as indicated by the luminaire manufacturer; an, J, }" Z4 v! W% N* Y' k+ z
electronic control gear clearly specified in the luminaire instruction sheet$ B% y4 t, J% u5 L
and a ferromagnetic control gear. The tests shall be carried out as required* {5 q+ \2 A* V# f
in Section 12 according to IEC/EN 60598-2-6 with the appropriate control
) f7 v1 N2 J8 H6 B: ggear., C- U! _/ J1 g7 v: Y+ L3 ]5 k- n
(*) When IEC/EN 62031 (34A/1168/CDV) will be published, it will takes1 u. M" X1 B9 \
over IEC/EN 61347-2-11.9 j' b: S% m+ B% B! @; K
(§) + A1/1997 + A2/2001
& [. o0 k7 F' x6 S3 G+ B(#) + A1/2002 + A2/2001, Z; N( g4 j1 l% _! c8 k
Explanatory notes: The matter is under discussion in Lumex/Comex; we will wait
2 c' @/ N3 w# y% @3 lfor the relevant outcome.# F1 ]0 }5 s1 H( X
# D% Y6 P3 y6 v4 B! t- {. A9 b
! P% m$ B6 `+ p6 q" |# n$ Q, v9 \ |
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？注册安规
x
|
|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网
( 粤ICP13023453-10 ) 
窥视卡
雷达卡
发表于 2012-9-17 16:34
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
抢沙发
千斤顶
显身卡
发表于 2012-10-8 09:30
