PDSH 994 Endurance test for built-in ignitors in the rectifying test circuit

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

PDSH 994 % l& q! k( B2 q, G , [6 I# W  G' f+ K8 U8 s2 G+ P

Endurance test for built-in ignitors in the rectifying test circuit 5 g8 j6 F! K/ Z$ L/ A1 k  G) j

12.1 – 12.2   n4 y8 E. x& z9 w, a4 x

60927(ed.3)

Standard(s):
IEC 60927/2007
Subclause(s):
12.1 – 12.2
No. Year PDSH 0994 2010
' _; Y4 I9 G5 ^Category: LITE Developed by: ETF5 OSM/LUM
* L7 ]. t" O* B; ?Subject:
) o! _5 n6 A( R# A" `* OEndurance test for built-in ignitors in the rectifying test circuit
Key words:
# Q! N+ d& B0 z( @- Test quantity
- Additional ignitors
- 30 days
8 e) W- e/ E/ W8 m( a1 oTo be approved at the 49th CTL Plenary Meeting, in 2012
Question:
- _; o1 f3 Y0 q+ t9 e/ ^# V$ a1) According to the § 12.1 of IEC 60927/A1 the test quantity shall consist of two additional ignitors for
. f1 X  _- u/ H& o, Xthe test as specified in the third paragraph of 12.2:
“Ignitors intended to be connected in series with discharge lamps which could, according to the
9 G4 X; z6 a4 x' f2 S) ?; Mspecification lead to ballast / ignitor overheating, are tested additionally under conditions with maximum
case temperature brought to (tc + X)°C and with rectifying test circuit in accordance with IEC 60598-1 V
Edition, § 12.5 and Annex C”.
In doing so, if we test ignitors intended to be built-in, without replaceable switching elements, the ignitors
shall be subjected to 30 days continuous operations so that the lamp current is adjusted to maximum (by
+ I$ U/ |& P- N2 L& B& c8 gvarying the resistor R2), but in any case not higher than three times the normal lamp current. The test
voltage is 1,06 times the rated supply voltage of the ballast. Our experience shows that some ignitors
7 f2 ?$ H2 T) H, A0 Ireach the maximum case temperature at room temperature in this circuit, when they are placed on a
6 [! f( |" ^, d, [/ H, H( z4 d" X6 fwood board. Can the test be performed in this arrangement and the type accepted if after the test both
ignitors comply with the relevant requirements? If the answer is no, how shall the test be performed?
2) Is it acceptable that the marking point for tc and (tc + X) would be at different places on the ignitor?
) R9 v5 o. B( N0 _Decision:
1 S" ^# `" L3 h4 t. Y! l6 N1 Y1) Yes.
; n+ |0 I* e$ f  m4 J/ t! k2) No.

& F9 F; D4 D: a8 \$ ~" F, N- p. y
! L* q( Q2 K- {. K
  z3 o- n6 X* u) F2 B' ~; a" U