DSH 700 Push force for connectors

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

DSH 700 % P! t$ q, }+ c4 U% \6 s3 A+ Z, q

Push force for connectors , i6 f3 J' {) e# K; R, J. R

4.3.5 6 m& q  a( I) Q* [; K. J0 P

60950-1(ed.2) + E) g- }/ i" t& R3 h" m; Q. j

Standard- No. Year
IEC 60950-1:2005 DSH
8 g% r  M) Z$ B  c) S. y, W& u0700
' B# i. J2 y9 }8 F3 ~9 O3 l7 p; W2008
Category: OFF
$ [: e0 p( X. c* r% r$ I" `Subclause:
4.3.5
# W; g2 b1 `) M9 H$ V" MDeveloped by: ETF 2
( _/ Z" y) L. v* u* q# ASubject:
' H* ?% |: r1 r( A8 kPush force for connectors
Key words:
# k4 v& E4 `* ^9 [-Travel adapter;
2 B0 ~- k5 \( [1 P, e+ a. y& P* [; W- connector misconnection
Decision approved at the
3 [0 U0 y5 N9 k8 q46th CTL Plenary Meeting
in 2009
Question:
* I" b# r5 I; f% m: D9 i3 n% ?A travel adapter consists of two separable parts:
·  AC/DC unit (down transformation of voltage, safety separation provided)
/ p% U" c4 [8 A0 s7 n( k; G& q  R·  DC/DC unit with output cable (supply stabilization and voltage adjustment, no safety separation
provided)
The unit can be used at AC mains (both units connected together) or DC (units separated, only DC/DC
1 q& Y; a: M/ Y) c/ r! A" \used). The AC/DC unit has a (Class II) IEC 60320-1 type appliance inlet; the DC/DC unit uses a
% T; l7 `3 P/ ~special 2-pins input connector.
With a small force applied (less than 30 N) an IEC 60320-1 coupler can be inserted into the input
4 M/ r" \/ H8 G' [connector of the DC/DC unit and make contact.
+ R2 f) Q9 S- i2 n. b' ^; W" C9 Ka. Is such design acceptable if a warning label is provided on the DC/DC unit and additional remarks
. N- C6 p% g7 d( ?. W/ j. b+ hare provided in the user manual that state that the connector of the AC power cord shall not be
pushed into the input connector of the DC/DC unit?
# D* c5 K; ?1 j$ ab. How much force must be applied during the testing of the input connector (DC) and appliance
/ \9 d2 v6 s/ P/ lcoupler (AC)?
6 @3 F! a6 {2 ?1 C* J5 @Decision:
A test force of 60 N (as specified in IEC 60320-1, no safety factor considered) shall be applied when
- w) [7 c9 n7 Q7 Ltesting possible misconnection of IEC 60320 and similar connectors.
/ c& ~- t6 g$ k$ [9 a9 ]4 T% r