|
| DSH 005/05( Z2 X5 T9 |5 N n8 Y. K
( E0 f1 Z- I) V3 W0 r! A @ | Luminaires provided with LEDs
: {% B9 J8 o9 H; ^ T | General Section 122 P1 N7 r% w4 _% p$ X
| 60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-2(ed.1);am1;am2 & 60825-1(ed.1);am1;am2
9 P9 e( a0 Z; a7 a |
: S0 H0 [8 w" DStandard: IEC/EN 60598-1/ G. w0 l3 ]6 ^! c1 i/ N' M
IEC/EN 60598-2-63 P: d1 ^: j/ B% E
IEC/EN 61347-2-2
* H$ A) k4 M/ C" E) F; MIEC/EN 61347-2-11* W" S! m. r! w$ s0 Y K* c$ W
IEC/EN 60825-1
+ }5 \ S4 Z1 n( q+ l5 `Sub clause: General
% x4 B, q4 E# |6 T: f# E" G2 T' MSection 12/ {( X- h; }7 l/ u# B: |
Sheet N°: 005/05
; [! k c/ ?3 _: y. nPage: 1(1)$ {3 f9 U" v3 m- S
Subject: Luminaires provided with# b6 H8 ]: o- Q$ H5 N
LEDs" X F+ k* w$ c5 i
Key words:1 f2 Q% R7 U( Q
- Control gears
* d. `3 }0 A5 j4 b& P; a- Section 12' T1 H0 N) b) L, | c2 D4 {! p
- IEC/EN 60825-1
$ c$ F+ {+ y) w# z" TMeeting:
8 d9 b- I8 t4 j5 `$ xCTL No. 42
# b1 }# `% C* |$ ` p6 S' d- j7 kWG1 No. 1 - 2 - 3
( D J% h3 P; }3 e8 w' |Item: 10.5.1* W$ B- n; q) ~) w- Y
Question: Is it possible to issue approvals on luminaires provided with LEDs light source?
" r F6 w8 q: `, f7 t. d# ]Decision: Yes, provided that:3 u3 a$ I. y# c) c3 H
(1) The LED circuit is verified according to IEC/EN 61347-2-2 (*) or IEC/EN
/ f4 q# b5 Z7 F61347-2-11. If the laser emits radiation in the wavelength range from 180 nm to 18 j+ h& Z n# c( P: ?# N& ^
mm, the LED shall also be tested according to IEC/EN 60825 –1 (Safety of laser9 r7 T: E- p) p
products). Only LEDs classified as Class 1 lasers can be used without problems9 V) O1 ^$ U6 K+ |7 r
for lighting purposes without protection.; ?$ d# G1 n$ ^: b6 h
(2) The thermal tests required in Section 12 of IEC/EN 60598-1 are carried out as
2 m% z! ~. a) p+ t+ p0 A) e" r: Rfollows:8 y3 m# `' m, G) b) ]% T
(a) Luminaires (Class I or II) with built-in control gear can be tested
( |2 |4 i6 F( q kaccording to the requirements of IEC/EN 60598-2-6.4 [& A. P$ V N$ X) u" ^1 R
(b) For Class III luminaires, the luminaires manufacturer shall provide on
9 k& p; @: g. E$ Q3 {5 ^$ ]: kthe instructions all the necessary information to supply the LED circuit) s4 D. B8 z+ B0 @; j5 d1 b
correctly or shall inform the Testing Station about the trade mark, the type: p* R; f& J1 D1 b3 k }# h1 ~
and the technical characteristics of the appropriate control gear. There can2 O* o e, q) k. Y
be three different control gears: the type and the trade mark indicated by the
/ v+ T4 ?6 W" T T/ Jluminaire manufacturer; an electronic control gear clearly specified on the
m0 Z8 E; T+ `0 n) X1 mluminaire instructions; a ferromagnetic control gear. The tests shall be ]7 [7 N3 e( ]
carried out as required in Section 12 according to IEC/EN 60598-2-6 with! b9 o U( U7 D! i* q2 L
the appropriate control gear.
$ W2 ?: ^% `0 J9 q/ I9 B* k) f& B(*) When IEC/EN 61347-2-13 will be published, it will takes over IEC/EN( {7 n, n2 j6 _0 R
61347-2-2.6 Y3 `9 Y5 }, l: P, r
0 _3 y% z, Q, W5 _. x6 f9 h: Y2 F
: t9 ~. }/ n: @2 B: H, F3 \) f* r |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|