|
| PDSH 005/07# P& m$ r' F! ]0 [+ r
0 h) q# j. d% m | Luminaires provided with LEDs, g0 }( B5 E8 U0 t
| General Section 121 a; s3 w8 u& w# `, l8 }, d! M! v& C
| 60598-1(ed.3);am1 & 60598-1(ed.4);am1 & 60598-1(ed.6);am1 & 60598-1(ed.7) & 60598-2-6(ed.2);am1 & 61347-2-11(ed.1) & 61347-2-13(ed.1) & 60825-1(ed.1) & EN 60825-1:1994
! R8 D0 A% ~' w L& A5 R( E' J8 |' {" u | & X* g1 H8 c6 |( {, @* a/ I" J
Standard: IEC/EN 60598-1
; O; U: L& c F1 ?1 I1 \6 SIEC/EN 60598-2-6
- C* g& V' ]2 x; z6 W# u1 KIEC/EN 61347-2-11; {. {9 d7 z1 [$ j
IEC/EN 61347-2-13+ ^% f5 T: w/ d3 Z& [
IEC 60825-1/1993 (§)4 t# o2 V' H# q" O/ {
EN 60825-1/1994 (#)
) |# Q: W6 p8 `Sub clause: General
' G) \( A7 B- w# QSection 129 }1 X( l1 z. w ^
Sheet N°: 005/07
- r. o8 H2 j5 u+ |* e( gPage: 1(1)
4 G8 e y R) U% u2 A7 [Subject: Luminaires provided with LEDs" J8 S) n# X" J3 p4 J/ y: Q
Key words:3 \8 @: G( x8 |4 X' q4 ^- d
- Control gears0 a" [) _! i g4 e R9 R, U4 t1 l
- Section 12
# f+ a, M( y5 n% {- IEC/EN 60825-1 (§) -1 v! ]$ O4 u6 A# k+ I' a
(#)
: j/ Q. |) i6 `+ [1 g8 o( jMeeting:2 r H4 {: t% W% o5 U
To be approved at
1 s/ r4 Q/ j& ?0 Z: [" e( O, D- @3 UCTL 45th meeting
' ?& d# V5 @7 v; UQuestion: Is it possible to approve luminaires provided with LEDs?# Q* V) Z% L8 Q6 J+ j! Z
Decision: Yes, provided that:
5 a1 n0 o- S! z+ `9 n2 p- the LED circuit shall be verified according to IEC/EN 61347-2-13 or IEC/EN
! I1 U9 o+ d7 d. J3 Q( }6 |- i, j- E61347-2-11 (*) and the LED shall be tested according to IEC/EN 60825 –1( D3 m. F ^1 g7 ], j' F$ ?4 M: R: x
(Safety of laser products) (§)-(#), if it has laser radiation in the wavelength
6 S& ? v. H3 o! J2 S2 P1 qranging from 180 nm to 1 mm. Only LEDs classified as Class 1 lasers can be" T L$ p& k: O6 |
used without problems for lighting purposes without protection.
: `6 C! {. S2 Z7 C! P- The thermal tests required in Section 12 of IEC/EN 60598-1 shall be carried$ \; Q1 |7 ]6 c( }. K
out as follows:
1 Y! c) [8 x$ H4 _1 T4 [4 G1 wa) Luminaires (Class I or II) with built-in control gear shall be tested) C, \ F& A _( E
according to the requirements of IEC/EN 60598-2-6.
% ~$ j+ l: O2 X% Kb) For Class III luminaires the manufacturer shall provide the necessary: v9 h% M2 ~# S+ n# n Y: E, Z
information to power up the LED circuit correctly in the instruction sheet.
[4 l6 D) ^, Y N) ~* @Alternatively, the manufacturer shall inform Testing Station about the; p5 x. S: u% A9 ~! M
trade mark, the type and the technical characteristics of the appropriate
3 R* b0 S- B, p- T a6 Z1 dcontrol gear to be used. There are three different control gears namely, the1 w; ^! h2 }" ~7 a- S
type and the trade mark as indicated by the luminaire manufacturer; an8 s8 w( h5 j! j4 g
electronic control gear clearly specified in the luminaire instruction sheet
+ }* _( a8 t3 V4 p" band a ferromagnetic control gear. The tests shall be carried out as required
& X0 ?% a3 y. ]- G) T m9 ?6 Q) uin Section 12 according to IEC/EN 60598-2-6 with the appropriate control
' A+ O) E5 {$ w) d, R$ M3 Mgear.* n2 C7 P: j X- d
(*) When IEC/EN 62031 (34A/1168/CDV) will be published, it will takes
; @7 B9 W; b3 p- Q8 X0 ^) b% jover IEC/EN 61347-2-11.
. `+ w; Q0 k7 |5 R$ p5 f(§) + A1/1997 + A2/2001
2 S! B9 G7 L/ Q5 X+ _, D(#) + A1/2002 + A2/2001# R: v& {( T: ]6 r C
Explanatory notes: The matter is under discussion in Lumex/Comex; we will wait
2 E5 w' |" |4 }+ ?7 }+ N& I. G. x2 Cfor the relevant outcome.
9 u* M7 s3 H; k0 n: B6 v1 _, ~3 M, B& n
0 H8 Y9 Z$ I# A2 w' e
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|