|
1 l7 b0 v3 T- \" c. t- c9 {5 mStandard(s):
( a9 ]; C; ]9 @. [) `+ Q o' d9 HAll IEC standards
% U: \" V" v" y% I+ ~* [) W, rSubclause(s):
- [1 p! [& ?- p4 `: oGeneral
. `# u& S, W* o1 S$ P7 f/ G3 x/ |" lNo. Year
% U) R6 q; N6 B- SDSH! }6 I3 u7 R& b6 X) u" ^" j
0791 2010
* y* I! q4 C2 d4 m A# R* l5 ^Category: VARIOUS Developed by: WG4
7 n/ @5 k+ F, L& |0 FSubject:
% n) {4 k- o" y. Y" XTRFs – Values to be reported
. e* f/ {/ W, r" B- |# _- ]Key words:
& q5 r: ?. P/ R! o \- TRFs
' I9 o6 R/ l' m$ R0 n( H; Y; y- Required minimum value( }9 u2 a* Y3 J
- OD-CB2020 Ed. 1.7 § 4.6.1
) E( h; e7 | h, UApproved at the 48th CTL
* T# { X7 m$ ?0 e" J" g7 XPlenary Meeting, in 2011! d' R4 @* A8 i: k/ \! ?% l% `/ E
Question:0 s% W6 s) D1 t+ M8 q4 g
Based on OD-CB2020-Ed.1.7 Sub-clause 4.6.1., it is not allowed to use statements such as “OK”, “meets
- d# k! z- C: V4 |6 rthe standard”, “more than”, “less than”, or similar instead of the measured value, unless otherwise4 F& v" S7 R3 G; i6 u3 L5 E3 W
specified by CTL.
: B& P! _* O$ G4 ?5 d$ Q& hIn certain cases the required minimum value is exceeded by a great margin.
# ^2 Y* T* X1 z6 \5 j. L: G3 |Decision:. T I4 |- e$ T2 o$ T6 a
In case that the measured minimum or maximum value is exceeding or is below the limit value for
/ I* G8 b5 n; V$ N Z) g1 Tmore than 30%, the value given in the TRF should be >[minimum required value + 30%] or should2 F7 Y5 C; P2 O# x/ o
be < [maximum required value - 30%]. The accuracy of the used instruments is in line with CTL
# O- Q5 X& V& B; r) D0 A* pDSH 251B or better.
& P9 n$ h$ {2 W$ v! H9 _4 pFor example measurement of insulation resistance:- c) X4 g* r0 v5 G; I6 g/ n
· required 5 M; Z+ f3 A% y* J2 r$ V& U
· measurement range of test equipment 0 … 10 M;$ t, K0 ^, W; N5 |
· the measurement instrument shows full-scale deflexion.
% S9 [& C- y- K& B! J4 R& JThe value given in the TRF should be > 6.5 M.
6 {% D5 o9 K$ B6 ]For example measurement of creepage distance:
# V4 H/ A. Q5 `. z" d. V- The required creepage distance is 3.0 mm.;1 y5 U+ Z" p9 N: T* M
- The real distance is exceeding 4 mm.;: B0 S7 F8 G4 i, p
The value given in the TRF should be > 4 mm.
2 d$ Z' L- {0 n7 ]' LFor example measurement of leakage current:
) R, H0 ^: o, N4 q* V$ }# _- The current limit is 0.5 mA;
5 \; D1 R7 J; N0 l0 F- The real current is below 0.35 mA;
( Z9 [; F3 e: \2 C( t0 h% S* [& aThe value given in the TRF should be < 0.35 mA.
) p* J1 ^" u2 [9 g M" B9 SThe following two situations are allowed:8 F" {* X9 K* v" F+ ]
1 – The meter reading is less than the smallest measurable graduation on a meter scale. For
/ T- G( X) b$ t; _4 I+ ^example, touch current measured was less that 0.1 mA.
& h8 b5 R% T, a- J7 g9 p2 – In checking creepage and clearance distances with a probe the same dimension as the
2 k2 h1 O' ~ B+ u$ prequirements. For example, creepage and clearance distances were greater than 0.8 mm.
, u% X6 u! P9 N* N9 Y2 A& p4 I- I" ^: u( w2 K
1 i' U# W2 q3 ^% p' B7 i
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|