|
+ ~1 V' ]0 u/ D0 u. a, A
1 _5 m& R5 E5 ^3 p+ A | Marking, Terminals And Operating Devices
" L" S% c) b& r D4 C1 X3 ^ | 5.1.6(f)2 D7 p- p' v* {+ A+ k
| 61010-1(ed.1);am1;am2
8 v6 {0 H m S. i5 @ | . w, k r: q$ a
Standard:+ w* P Q. V: X) ]( U/ j
IEC 61010-, \/ q9 L4 A+ P) @
1:1990+A1:1992+A2:1995
5 q6 z7 @2 H3 wSub clause:6 d( c; v/ O3 y. O7 H
5.1.6(f)
+ Z. q7 }: E/ ^$ C8 g. ESheet n. 298: ^4 q x! a5 [) b( a( W: Z6 s
Page 1(1)
$ H2 Z7 w3 r2 L/ K0 R+ j. wSubject:) {/ A2 c$ v. M* G
Marking, Terminals and Operating" I4 f( \% d/ E
Devices
& T: Z3 M/ z: ~) _Key words:: t+ R+ X( r* E& t# I
- Marking0 {) \7 b$ L- E1 t
- Mains9 w6 t7 |2 `/ {. ]5 F! T, t
Decision taken by
; a# N; |" e1 oETF3 and confirmed
6 n9 s6 x: U) pby CTL at its 38th+ e) w; @, Z5 |+ L
meeting, in Toronto6 Z5 I. g4 w6 v3 b+ `6 p
Question:# B! I- p3 H+ S0 n
Can symbols 9 and 10 of Table 1 (0,1) be used for any other purpose than mains" m$ F q4 |/ q# K3 t8 ]0 \7 n1 H
disconnection?
& c# { u) d4 pDecision:
. J- {; N U8 z7 B6 v' n# p. jThe standard states these symbols are reserved for mains disconnection devices, the symbols1 v e3 \; c! e7 Q
should therefore, be used only for this purpose. However, these symbols are allowed for
( Z% B% A1 S4 jother use in other IEC standards and some Test laboratories therefore, exercise discretion on5 c( O: K/ \) T6 r$ K @# k
this matter provided the mains separation device is clearly indicated either on the unit or in
1 ^4 N9 }- v5 W/ O- ]the handbook." C. p: M/ s: F1 {- Q
Explanation:
+ j2 s8 |. Z$ O5 H: kIt is likely that the use of 0,1 symbols will be reviewed across all IEC documents and,
- m2 f( f Z% G# [. T$ [# Wpending this review, it is important that the mains disconnection device is clearly identified$ u |2 c5 a+ Z7 _1 o
either on the equipment or in the instructions for use.; W& x3 |' c+ K
3 ]0 K# k0 u! P1 w& h! l# E# ~- r3 J9 Z9 X- t' l
: Q( F+ W* `* Y. P3 P6 Z9 e |
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|