|
请教高手9 r4 o: z( b+ F/ s) G% J
; U* j0 a+ u Y5 X* ]6 IIEC/EN61010-1:2010 对跨接初级与次级Y电容有什么要求。
+ G3 |+ ^: l/ \& ~+ o现有:( d' f: j4 w* ?# J u7 T8 u4 ?
CY1电容器跨接在初次级上,满足加强绝缘距离要求。
# q. ^ P2 J* E6 c5 g# Z- q
8 ^( k" w1 _" i, X8 D N6 k认证公司要求:0 }1 m! d8 m& [ d$ W Y
1. CY1电容耐压值应该更换为500V5 @' W) @$ A" \# S9 o! H9 p
2. 或者采用两个CY2串联1 o. j& k/ h% f0 o% Z
0 k8 f& ?! D! o/ l* L$ d
目的:因为EN61010-1标准要求CY1必须要有2倍工作电压的耐压值
/ f9 \6 T& N* C7 _
u( V& V5 c4 Q6 Q3 L7 R( t( K1. 我想知道他们所说的耐压值什么意思?) x M2 o1 v, M: j Y) `
6 C& t c4 o$ k* E- N, l2. IEC/EN61010-1:2010 是说的这个意思?; J( S* u0 w8 I
. x) t7 Y' F6 U; C w9 \7 v; I
下文为标准:
8 k; j# L6 c' N3 U* i6.5.4 PROTECTIVE IMPEDANCE
5 @9 U& L1 {) M; c8 mA PROTECTIVE IMPEDANCE shall limit the current or voltage to the levels of 6.3.1 in NORMAL" i5 W4 c& m2 C+ B5 ^, k
CONDITION and 6.3.2 in SINGLE FAULT CONDITION.
' ?. ?) x8 W3 x7 \: p8 Z/ } c# ~0 H, y: t& A( J/ B% {1 p
Insulation between the terminations of the PROTECTIVE IMPEDANCE shall meet the requirements
$ M3 [* y& e5 H# r& @of 6.7 for DOUBLE INSULATION or REINFORCED INSULATION.
# B6 B) T9 C0 _4 T: ]! o
* E( o2 Z6 x! q( C& O6 YA PROTECTIVE IMPEDANCE shall be one or more of the following:$ c/ j% h! d7 r `9 Q3 x9 J& X
& K9 S% s9 q# u3 t" ma) an appropriate single component which shall be constructed, selected and tested so that safety and reliability for protection against electric shock is assured. In particular, the component shall be:
3 p% u' G/ M7 O; K" o6 ?+ F5 Z
T. R. @; e5 R8 D& o* X- }3 N1) RATED for twice the maximum WORKING VOLTAGE;
# g C+ d5 \- c6 k* n5 W
6 h9 Q, M, Q' w, b7 C% T$ C2) if a resistor, RATED for twice the power dissipation for the maximum WORKING VOLTAGE.7 l( C# O* \# I; ~+ A
0 J* Q7 b8 R. S" e2 eb) a combination of components.
, i4 L+ \% `( z/ v: Q3 tA PROTECTIVE IMPEDANCE shall not be a single electronic device that employs electron
I! @( F4 V* |' Qconduction in a vacuum, gas or semiconductor
8 _7 ^) d+ Q7 K0 d6 T8 fConformity is checked by inspection, by measuring the current or voltage to confirm that they
7 W# ~" E- A2 ?9 Sdo not exceed the applicable levels of 6.3 and by measuring CLEARANCES and CREEPAGE1 t, q* w8 R( T' X4 q7 O
DISTANCES as specified in 6.7. Conformity of a single component is checked by inspection of
7 Z/ q7 I/ V. f' Mits RATINGS. |
|