关于UL1082标准7.11疑问

myhet

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

7.10 An opening in the enclosure that has a minor dimension of less than 1 inch (25.4 mm) is acceptable
1 C( H* |' g6 a0 }, l3 @* b' c; P) ^if a probe as illustrated in Figure 7.2, inserted through the opening, cannot be made to touch any
uninsulated live part of film–coated wire that involves the risk of electric shock. The probe shall be applied
. q* {, }% |; Y! P# N; g& gin all possible articulated positions before, during, and after insertion.
7 H. s) H+ @) E" c7.11 An opening that has a minor dimension of 1 inch (25.4 mm) or more, in an enclosure, as illustrated
in Figure 7.3, is acceptable if, within the enclosure, there is no uninsulated live part or film-coated wire
less than;
a) R distance from the inside edge of the perimeter of the opening and
b) X distance from the plane of the opening.
0 Q- H( h3 D# n) v( AT equals the enclosure thickness, R equals X minus T, and X equals 5 times the diameter of the largest
  z& u0 a0 B( xround rod that can be inserted through the opening but not less than 6-1/16 inches (154 mm). In
evaluating an opening, any barrier located within the volume is to be ignored unless it intersects the
boundaries of the volume in a continuous, closed line.

7 J& j0 }2 ~, q. v0 N$ f: E7.11是否说在一个符合7.3描述的外壳上，当有大于或等于25.4mm的开口时，如果在外壳的以下范围内没有uninsulated live part or film-coated wire的是可以接受的？
+ A0 O) J0 f" l" @" i这个范围是：A，从开口内边角算起的R距离间。R=外壳厚度+X
, C) ]4 y  _- S. M' Q- q$ Q# m            B，从开口平面算起的X距离间。X=MAX.（5*Rod直径，154mm）

simondai

个人理解:
9 U: V& N; o* a* [5 J7.11 当产品的外壳上有如图7.3那样的一个开口,并且此开口的最小边长度大于等于1英寸时,如果能够满足：

Ａ）在以开口内边为中心，距离为Ｒ的周长范围内，同时
Ｂ）距开口外表面Ｘ距离的范围内
, t5 m$ `/ p5 M" _
5 Q3 o+ ]" l9 q5 H6 h# K没有任何未绝缘带电体或者漆包线，则认为是可接受的．
% ~( w" i/ m9 E0 x% C% ]# ?
6 K1 u" y) G& l' l3 S% rＴ为外壳厚度，Ｒ等于Ｘ－Ｔ，并且Ｘ应当等于最大可伸入开口圆棒直径的５倍但不应小于６－１／１６英寸．在评估开口时，任何挡板都应当被忽略除非该挡板在外壳上的投影可以和开口２边外壳形成一个连续封闭的线．