DSH 734 Application of bursts on cabinet earth point

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

DSH 734 3 ]- I3 c' ~0 ^; O( s

Application of bursts on cabinet earth point + w( w" k* C* e1 g

7.2.2.3 and figure 11

61000-4-4(ed.2) + u. l2 b9 h- ~4 p- s/ J

Question:
For EFT testing, IEC-61000-4-4: 2004, Clause 7.2, test set-up for type tests performed in laboratories, has 3 conditions for coupling the test voltage to the Equipment Under Test: Clause 7.2.2.1 Power supply ports, Clause 7.2.2.2 I/O and Communications Ports and Clause 7.2.2.3 Cabinet Earth Port.
- }$ x* q, h5 X! ^: o. U4 SFor power supply ports ,Clause 7.2.2.1, Figure 9 is referenced which indicates a common mode coupling. So for a single phase product with a PE conductor, the coupling would be L+N+PE and for a 3 phase product the coupling would be L1+L2+L3+PE or L1+L2+L3+N+PE. This is fairly clear and straight forward. However, for the cabinet earth port, Clause 7.2.2.3, the standard states: "The test point on the cabinet shall be the terminal for the protective earth conductor…" as shown in Figure 11. Figure 11, reproduced below for convenience, is for post-test installation tests and for floor standing devices. Yet, if you look at figure 11, the PE test point that is referenced in Clause 7.2.2.3 is the same test point as PE in the supply port coupling path.
  d6 N* t* v& ^% w* i4 NFor laboratory tests on any floor standing or table top product, should the PE port be tested as a stand alone test point after the application of the common mode test on all lines, including PE, or is this a test only applicable, if a separate earth point is provided on the product?
  W/ u( }; v9 E* E% d2 LIn other words, does PE get tested by itself since Clause 7.2.2.3 indicates the test point on the cabinet shall be the terminal for the protective earth, or is it sufficient to indicate that PE complies when tested as part of the supply port (for example L+N+PE) as long as a separate cabinet earth point is not available on the product?
+ C) j" g8 S6 I: I8 c5 ?Decision:
PE as a part of the mains cable is not the same as the “cabinet earth point”. The test on the “cabinet earth point” will only be applicable if called out in a product or a product family standard. It is removed in the most recent versions of generic standards. Clause 7.2.2.3 addresses additional earth points on the cabinet, if available.
, z0 `2 a$ U' C# G' q4 o) s* g
9 l3 T. H3 M; ?8 r

2 |5 {$ k9 t- e& S2 m& L: h- ~