|
| DSH 4452 i2 y, q! F9 y _
4 @- i9 N3 S' Q4 N3 Y: k3 \ | Protection of users
: [9 d4 p' Z& I" s L, C | 7
7 M* z" J$ V0 ? | 60950-1(ed.1)' A \6 X( k3 M7 ~
| " l" c' g `- p8 Y f& i
Standard:! l+ W: F4 z* J0 r+ \
IEC 60950-1:2000, 1st ed,
& b+ j. X, Y+ b2 T5 \* ASub clause:+ U, p7 W% k+ s( D3 H0 _
7
: b6 e6 `/ }; g6 D( l9 X6 T9 q/ kSheet No.( B. G, }2 h2 V( o; k. z
445
8 u- a' S; O2 Y" G) q/ MSubject:
5 P1 C& V3 L: W& a! d1 T- g: KProtection of users7 D. q" O8 ]+ [! T" O
Key words:7 ?! y# ?8 i9 T# d# |
Antenna, voltage surge test E4 ~2 I: `0 l, I6 R. K; R+ V
Decision taken at the m8 ` V- ~" e [5 T9 p8 ?; \8 [
40th meeting 2003, a$ P, z7 s/ w) \, p1 y
Question:- q/ J/ F7 v7 M: a" a
For protection of users and service persons from transients and voltage surges, what are the appropriate* l3 K7 r' R. u4 C
requirements between the following points for ITE connected to an external antenna:. r( s0 t6 l3 @
(a) antenna connection and Primary circuits?7 t0 x( n* I/ ^( }6 r! O( j0 I
(b) antenna connection and SELV circuits when the antenna cabling is coax?
( v; k4 U, u3 J2 ?" A1 A% f(c) Antenna connection and SELV circuits when the antenna cabling is unshielded twisted pair* K. K% h9 E, t4 a4 Z3 U; A8 I
(UTP)?, \9 i8 I& `, f" v% Y. r
See attached diagram.9 P& t& ? u( d, @, v' B
Decision:1 _4 h4 p$ L( u( G% Q) Y' N& p- ?5 ^
Since Clause 7 is in IEC 60950-1, but is not in IEC 60950 3rd Ed, all references are to IEC 60950-14 Q# h* @# b" ^
The circuit connected to the antenna is classified in accordance with Sub-Clause 7.1 and subjected to the7 j# B0 V, d& g3 s) @: C# ~6 Q
appropriate requirements per 7.1. Additionally,
) E' ~( i! u( g$ K(a) Sub-clause 7.3.1 is applied between the external antenna connection (terminal) and Primary% H6 W2 h. Z* y1 O9 V' d
circuits.
9 I6 o6 H$ n7 M) e(b) Sub-clause 7.2 is applied between the external antenna connection (terminal) and the SELV
1 r5 I7 _( M$ j1 ^- zconnector (RJ -45) when the antenna cabling is coax.
" t: a" ?1 h! _3 g$ V) ]3 _+ V(c) Sub-clause 7.2 is applied between the external antenna connection (terminal) and the SELV$ \7 I o! r( ^- k/ [3 u
connector (RJ -45) when the antenna cabling is UTP.
9 m# y& H2 J; j$ X$ i$ r4 C+ l; Y p* d7 h/ }
" z) v+ m P+ x/ z/ I
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|