|
|
协调标准（HD21和HD22）在2014年1月份需要换版为EN50525。 届时，HD21和HD22标准将作废，所涉及的所有PVC和橡胶线VDE证书将必须在此期限内完成EN50525标准更新。# c2 B! A- I- x4 A. n7 V# O
/ L- Q4 n2 v' b
站内似乎还没有说明新旧标准的差异，新标准也还没有发布。现提供以下信息，供各位参考：+ A; G& o( g7 V/ |1 b# x/ L
（这些信息仅为草稿件，不能保证将来新标准发布时会完全一样噢）
: }' d& u2 G$ Z7 q. R Y4 @9 R( k
/ A( C5 w5 a$ f9 ?+ ^举例： 以H03VV-F为例，需要进行的额外测试有：" {0 C2 t, Y4 p* F0 D
cold impact at -5C( 旧标准为-15C)2 L6 {+ e& f+ P% Z A; q
增加non-compatibity test(旧标准没有此要求， 只有compatibity test）% O4 ~& m' E" Y$ B0 _
bending test
; I) T4 w7 Z5 g' zvoltage test （2000V） after bending test（旧标准在bending test后没有voltage test 的要求）
9 \) Z1 w* ~7 i; O0 w
1 ]; X! R( K' u# ~; `. r0 a0 ?0 }, Y虽然新标准尚未发布，为避免项目塞车，现在即可向VDE提出申请。
' ^- x7 j) R$ @: S2 V
% v' } s2 S- T# v2 { RDIN EN 50525-2-11 H03VV(H2)-F) C: A& B2 a; }5 ~% |4 \! o
Cold impact test at -5 °C
- u- E' D$ f4 v( [0 J2 N1 Tnew: non-compatibility test
- _1 m( {' H) y9 N
) I& F$ S7 p: _! ZDIN EN 50525-2-11 H05VV(H2)-F% }8 a/ x! }& Z
Cold impact test at -5 °C
* R1 W5 s# r' u2 znew: H05VVH2-F 2 X 1,5. y6 l% d7 Q: v+ o+ }
9 l: S" ]1 a. M: a
DIN EN 50525-2-11 H03V2V2(H2)-F
! I& z2 [) ^8 M& |% T- y0 Q0 G* NCold impact test at -5 °C2 v9 q; W4 N8 p4 h) Y1 j5 @
new: non-compatibility test- n" U# r/ U' _# t0 U/ C
# h7 F1 L* P! x( t# ~
DIN EN 50525-2-11 H05V2V2(H2)-F5 p( w# u# O/ i2 D) S% w
Cold impact test at -5 °C; E( ?; ~. L" |' T
new: H05V2V2H2-F 2 X 1,5
" X* x/ _2 i: H, M/ g( H Q: ~" |8 X! j( c0 T
DIN EN 50525-2-11 H05V2V2D3-F
3 X" \ T3 [! _: c7 c) eCold impact test at -5 °C
: L' `* u+ T3 I! rFor all types: Voltage test after bending test with 2000 V
% e8 ~ y* E4 {( [- W----------------------------------------------------------------------------------------------------------------------------------------1 a L' [8 b: p. R
DIN EN 50525-2-12 H03VV(H2)H8-F
+ S1 P4 E* v0 `) tCold impact test at -5 °C6 O9 V7 m% Q2 J, G) w
new: non-compatibility test% r, K# L. z4 e# B; I
New requirements for the marking after coiling# ?1 ?" _7 q- _
" l; q& y8 c; }DIN EN 50525-2-12 H05VV(H2)H8-F
& s9 ~0 B- R4 ~$ I0 z yCold impact test at -5 °C1 c+ J+ |: g& C. D
New requirements for the marking after coiling, b/ x5 X g3 a* @" _
3 V: Y6 g r+ V6 q! y
DIN EN 50525-2-21 H05RR-F
% Z4 b$ s7 A" }) P4 \4 Lnew: cold bending test for the insulation at -35 °C; t2 f$ n$ U+ i" A4 c9 p. w, z( l L
+ j! b w+ u. E2 s1 Q- G
DIN EN 50525-2-21 H05RN-F3 i- h8 X$ J' B$ s" J% j- d( p* ?8 q
new: cold bending test for the insulation at -35 °C
/ b- w$ r5 S. Cnew: H05RN-F 4 x 0,75 and H05RN-F 4 x 1: f) t; u; M9 {$ P, s8 ?
" {. I3 ]' u' e' J0 I' Y: c- bDIN EN 50525-2-21 H07RN-F, H07RN-F vieladrig+ u% q# `3 p( e @ _! T/ L
new: cold bending test for the insulation at -35 °C; C& w3 n* ]0 S7 @' R
9 i& g$ O j( f" E$ L% oDIN EN 50525-2-21 H07RN8-F
& x; J( F( z9 D3 dnew: cold bending test for the insulation at -35 °C2 l# f/ n/ y& A z9 s3 P, C9 A) |
4 x+ S% J0 ^/ U% Y9 O
DIN EN 50525-2-21 H05BQ-F! Y0 u# T7 O6 f3 R
no changes
% Y/ b; W( S. A$ ` z, dDIN EN 50525-2-21 H07BQ-F
! ^, L) d5 p" Xno changes% C# `) y% b1 F. L/ k% Y" A; A' q2 R
DIN EN 50525-2-21 H05GG(H2)-F
) m3 N. h; ^, j) j, Q9 Bno changes. q( m% S' v' R- l6 f4 r
DIN EN 50525-2-21 H05BB-F
2 m4 | ^) R3 A4 dno changes* U( p. d+ j* N% W+ Q9 I
DIN EN 50525-2-21 H07BB-F
7 [( Q4 t, u, C: f. U. q0 I" g6 ~no changes! u0 k* P) d$ F) S1 b9 [5 p, _
DIN ENDIN EN 50525-2-21 H05BN4-F
; k) Q. ^( t+ r. gno relevant changes3 h5 y6 I$ c N" S
DIN EN 50525-2-21 H07BN4-F, H07BN4-F multi core) L9 g: X2 r3 P
no relevant changes$ A! ^4 N1 K, B% O( h _9 i! V5 {
----------------------------------------------------------------------------------------------------------------------------------------9 U1 Y- P% i" `% Q1 q, h
----------------------------------------------------------------------------------------------------------------------------------------
+ \8 H! a6 B8 z& P# WDIN EN 50525-2-22 H03RT-H# z E2 I. q- J9 C5 ~( @9 e
no changes0 l% f7 y R2 I" y1 l2 Z
H05RR-H und H03V4V4-H withdrawn; G2 A: y; x) U; T! @2 i$ m
----------------------------------------------------------------------------------------------------------------------------------------
! x+ d/ u- ^" O& i b; hDIN EN 50525-2-31 H05V-U/-R/-K
0 ]; N1 h5 Z! {- y$ l1 N, N! dnew: Cold impact test at -5 °C
7 e0 ~; d0 l" H9 A5 }; S u3 b
K- a1 U8 Z8 F, l, Z1 }DIN EN 50525-2-31 H07V-U/-R/-K1 S% k0 X* e/ ~ E$ `8 d, K+ \
Cold impact test at -5 °C (new: -K)0 G$ C' N+ ^$ m5 y4 V6 }5 T
0 D. p: T- D0 C5 Y* w9 q n
DIN EN 50525-2-31 H05V2-U/-R/-K1 |3 T) O* q; J5 D& l
new: Cold impact test at -5 °C
: P v, |& @2 s6 C( ]7 {0 K# ?4 K& u. y* S
DIN EN 50525-2-31 H07V2-U/-R/-K
5 m1 Y5 ]0 B& PCold impact test at -5 °C (new: -K)- _! r6 }0 n& i3 |
----------------------------------------------------------------------------------------------------------------------------------------. I; n- W% ^; E6 F
DIN EN 50525-2-41 H05S-U/-K k& X$ v. ~5 k9 C1 q6 a
no changes) B( m A% d; ?
DIN EN 50525-2-41 H03S-K) t, G1 ?$ g, x, N7 v
no changes8 b* S& k: x# o" a" H8 [
DIN EN 50525-2-41 H05SJ-U/-K# V% t5 j6 X2 a* l+ n& ?( e
no changes
; C& j& n- G! RDIN ENDIN EN 50525-2-41 H05SS-K5 R2 [: ]) ^( d
no changes
+ u# \6 d6 {5 ]5 R |$ U( U----------------------------------------------------------------------------------------------------------------------------------------
$ p, n @: h9 l7 cDIN EN 50525-2-42 H07G-U/-R/-K
! b y C; j6 p4 ]5 |7 M8 fCold impact test at -5 °C
, q$ H$ H# z9 n) _$ t1 l2 V4 u# c1 n4 d
DIN EN 50525-2-42 H05G-U/-K
+ f; x1 v7 ~6 @! Z% Z- k5 V8 X1 f# vCold impact test at -5 °C
; ]0 o5 ~1 r, M; V/ D, x----------------------------------------------------------------------------------------------------------------------------------------( W) }9 E' \4 Y0 U
----------------------------------------------------------------------------------------------------------------------------------------
( o' m6 e5 j) SDIN EN 50525-2-51 H05VV5-F# p; s+ n$ g6 p/ |
The cable shall be marked with the code designation ``H05VV5-F``
( B: N' z% N' S& ACold impact test at -5 °C/ p" Q# [& |8 x6 P! p
1 S( f$ O5 p) ^
DIN EN 50525-2-51 H05VVC4V5-K; M r# A- O: C5 s& a# h9 B( }$ M7 r
The cable shall be marked with the code designation ``H05VVC4V5-K``3 t. f% ?2 T, X& b
Cold impact test at -5 °C- C* z' F) o2 p
changed calculation procedure for cables which number of cores does not belong to the preferred
) z+ w8 P5 H( D- z! D* ?" Pones
, Q- X: R- X z, X ^----------------------------------------------------------------------------------------------------------------------------------------, B1 Q% e, G3 s4 r% l+ L
DIN EN 50525-2-71 H03VH-Y
8 @# m7 K7 T, C9 R3 H: e# |9 x, @new: Cold impact test at -5 °C+ i7 S% s+ ?3 e$ j
----------------------------------------------------------------------------------------------------------------------------------------
, M. a v+ d* }+ o( L4 J; d5 ` @0 GDIN EN 50525-2-72 H03VH7H-F
5 F* t# X7 R& P5 WCold impact test at -5 °C
6 O0 j3 d2 J+ V) z3 `: v9 X----------------------------------------------------------------------------------------------------------------------------------------
: N" p; @7 y! B! V2 ^4 O0 H* EDIN EN 50525-2-81 H01N2-D/E
! i* A$ J+ k9 L- Q/ r& fextension to 240 mm²
- `" E3 f: N2 f2 i1 s% u----------------------------------------------------------------------------------------------------------------------------------------3 j6 [, }: M2 d' }* c) u+ G1 T
DIN EN 50525-2-82 H03RN-F. Z, ^# K4 ]5 L* l
new: Cold bending test for the insulation at -35 °C
) D0 f x/ e: V8 }- e) c. r
, {9 q x" L" Z" b: [' b B* } hDIN EN 50525-2-82 H05RN(H2)-F' w$ V/ c/ t# _7 f+ q( V
new: Cold bending test for the insulation at -35 °C+ L; s. T4 P1 {6 E2 I b
----------------------------------------------------------------------------------------------------------------------------------------2 l+ \2 W( ~9 R$ q: |
DIN EN 50525-2-83 H05SS-F; H05SST-F
1 A5 s1 @1 A# Y6 NThe insulation shall be a single layer
' B+ Z* ~, D+ O# L3 T( F. L4 _4 S5 ^" @
DIN EN 50525-2-83 H05SSD3-K; H05SSD3T-K
# x. K* E F( B9 B. JThe insulation shall be a single layer N, D2 }7 J1 \, m
-------------------------------------------------------------------------------------------------------------------------------* @! R4 B/ J& H2 f# b p
----------------------------------------------------------------------------------------------------------------------------------------& N' z% @4 |# `/ L) s
DIN EN 50525-3-11 H03Z1Z1(H2)-F
& |+ \( v1 X- Q+ eCold impact test at -5 °C
, t2 I: F$ Y" I% d5 p8 M4 `7 b, y" n
6 n# E4 R" j, e6 ]DIN EN 50525-3-11 H05Z1Z1(H2)-F5 u6 l# q. p7 u* e
Cold impact test at -5 °C
* ~1 U* U. e+ pVoltage test after bending test with 2000 V
' U; z6 i. Q8 }9 F----------------------------------------------------------------------------------------------------------------------------------------, o1 Y0 @9 d( o e4 |
DIN EN 50525-3-21 H07ZZ-F
) W- R5 H8 ] Z/ Pnew temperature for compatibility test: 7 d at 100 ± 2 °C (old: 80 ± 2 °C)4 n4 ]& h+ R) W( e$ T/ Q
---------------------------------------------------------------------------------------------------------------------------------------- c. {2 _. m8 k! i6 \
DIN EN 50525-3-31 H07Z1-U/-R
. a, }5 h- }4 Z4 t8 {, NCold impact test at -5 °C) R& |4 a- s) k: N! n) U3 R) c% m, `
: S$ @+ k% a5 X- a4 i! D
DIN EN 50525-3-31 H07Z1-K
& J* o& r5 x) N8 `4 Q8 V) eCold impact test at -5 °C
, j, y1 @2 K5 o. v
" @/ w g) O6 Y: g' B7 uDIN EN 50525-3-31 H07Z1-U/-R+ J. F+ F' o" c* t6 L `! r
Cold impact test at -5 °C
" l% S, @; f8 y& w8 _2 O5 u: z
' L2 D8 K$ \" `& ADIN EN 50525-3-31 H07Z1-K
- S5 W# \, m+ A8 yCold impact test at -5 °C4 d9 R) f: ^$ W& ^* y# S
----------------------------------------------------------------------------------------------------------------------------------------# c. o% j3 M+ V) p% V! O/ E0 q
DIN EN 50525-3-41 H07Z-U/-R& {: d. ~6 O6 ^6 l& u
no changes
+ u/ a$ Y) T; NDIN EN 50525-3-41 H07Z-K
; K" C/ ?- _ `% }8 m0 ?7 Fno changes2 E2 r2 G7 B& i' Q
DIN EN 50525-3-41 H05Z-U
& H8 V5 Y2 f$ ~$ p# mno changes
5 f( I+ d4 j/ M: kDIN EN 50525-3-41 H05Z-K" Z) }) C& e6 I8 d R! L0 S
no changes% h. l2 }( G4 |" Z: Q3 ^0 W
----------------------------------------------------------------------------------------------------------------------------------------
6 l9 }' u- V; m( k t0 W举例： 以H03VV-F为例，需要进行的额外测试有：
$ R+ P) r, }6 r+ t& Y, g, vcold impact at -5C( 旧标准为-15C)
: p) n2 T( O( B2 K! n8 H增加non-compatibity test(旧标准没有此要求）' H* Q% v" N, ~9 B4 S" O: {7 g( h
bending test5 h6 g9 j8 M% j' X& d
voltage test （2000V） after bending test（旧标准在bending test后没有voltage test 的要求）
* `6 n; b1 Q, Q2 ~7 \. Z6 A
9 ]* a* c. P9 T6 G" }* C% o虽然新标准尚未发布，为避免项目塞车，现在即可向VDE提出申请。
y8 S n" A$ n: ?4 D- g1 @* K: \2 U1 F' L/ h1 Y
|
评分
-
查看全部评分
|
/2 
|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网
( 粤ICP13023453-10 ) 
窥视卡
雷达卡
发表于 2012-5-3 17:11
收藏
分享
好帖
鸡蛋
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
抢沙发
千斤顶
显身卡
发表于 2012-6-30 16:24
