关于EMC整改

lewis.zhang

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

关于产品EMC整改的一些问题请教各位：
% H1 K# n) R/ w% w' i: T我们一款产品EMC测试出现以下问题整改一直不过，
2 {( L6 v7 W* |$ j5 o
! {- M( z# {5 W5 k- ^/ Y8 r1，产品金属外壳，有一块塑料面板上有一液晶显示屏，显示工作电压之类，静电抗扰度空气放电8KV时显示屏会花。不能自动恢复，只有重新开机才可以恢复。有什么办法？

2，传导整改后曲线很好，很低，但就是在150KHz处有一个尖峰超过限值。请问是什么原因？有什么整改方案？
( O  p2 u& D1 V# [
3，辐射整改不过，没有余量。
: Q1 l% @/ n7 M6 G% y( T2 o8 E2 ]
# O. H1 T* ]3 H. o- \* R谢谢！

kamleung

May I know where the air discharge is applicable when the ED problem occured,
, }$ O  C! B( `. \4 j           -  near the edge of your plastic cover, or
           - at the centre of your plastic cover?

lewis.zhang

near the edge of the LCD screen.

kamleung

As your product is made with metal case, the electrical charges will jump onto the metal case when the ESD gun is closed to the edge of LCD screeen. Then, the elctrical charges are brought to the system ground through the metal case. That means the pins of LCD display should be shielded by the metal case and therefore the controller IC will not be affected by the ESD charges. Any way, may I know whether your metal case is grounded or not?

lewis.zhang

The metal case is grounded, and the LCD display screwed on the plastic panel.

lewis.zhang

引用第4楼lewis.zhang于2010-11-16 14:13发表的  :
The metal case is grounded, and the LCD display screwed on the plastic panel.

kamleung

To make further suggestions, just to confirm the arrangement again with the two pictures. If any of my undertandings are wrong, please feel free to correct me.

bob_dai

楼上的蛮专业

lewis.zhang

The LCD display and the black panel are plastic, no metal used in the two pictures.

kamleung

As the black panel is plastic, it cannot help to protect the LCD display. The electrical charge may creep towards the pins of LCD when the 8kV ESD gun is applied. Two suggestions  are made in the above two pictures. Hopefully, it may help.