什么叫应力测试

wzy-007

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

请问什么叫应力测试

awen

我们这里有测试配管应力，但具体不知道怎么解释

caballo3157

应力：当材料在外力作用下不能产生位移时，它的几何形状和尺寸将发生变化，这种形变称为应变(Strain)。材料发生形变时内部产生了大小相等但方向相反的反作用力抵抗外力，定义单位面积上的这种反作用力为应力(Sress)。按照应力和应变的方向关系，可以将应力分为正应力σ和切应力τ，正应力的方向与应变方向平行，而切应力的方向与应变垂直。按照载荷(Load)作用的形式不同，应力又可以分为拉伸压缩应力、弯曲应力和扭转应力。(------引自百度百科)

自然对应力的测试就叫应力测试。不同产品，不同材料，应力的测试方法和仪器各有不同。

Leo-Mo

在标准上有没有对“应力”的定义？

fasten

16.4 Mold stress relief
' G1 \* P3 m% m; d16.4.1 A sample of the complete thermoplastic enclosure shall be placed in a circulating air oven and
0 H& I. A9 _6 X' m2 {maintained at a temperature 10 °C higher than the maximum temperature measured on the surface of the
0 p; a; A- s" \8 |8 Tenclosure during the normal temperature test but in no case less than 70 °C, for a period of 7 h.
16.4.2 After the sample has cooled to room temperature, the sample shall comply with the applicable
( J: F% f$ v9 `9 w4 Grequirements of this Standard.

longer

EN60950-1:2006
4.2.7 Stress relief test
ENCLOSURES of moulded or formed thermoplastic materials shall be so constructed that any
. M* x. z) g- k/ d+ _, D, Dshrinkage or distortion of the material due to release of internal stresses caused by the
) s  s$ |# K8 E' I  J  I4 _0 Gmoulding or forming operation does not result in the exposure of hazardous parts or in the
- P7 \& k% z8 e0 X4 vreduction of CLEARANCES or CREEPAGE DISTANCES below the values specified in 2.10 (or
Annex G).
1 ~/ v' H+ b. _8 ACompliance is checked by the test procedure described below or by the inspection of the
# }& g: B0 h8 e1 Rconstruction and the available data where appropriate.
One sample consisting of the complete equipment, or of the complete ENCLOSURE together
6 @) K# {: \8 }' C. E) d6 vwith any supporting framework, is placed in a circulating air oven (according to
IEC 60216-4-1) at a temperature 10 K higher than the maximum temperature observed on the
: |+ s( K8 }. C. eENCLOSURE during the test of 4.5.2, but not less than 70 ° C, for a period of 7 h, then permitted
to cool to room temperature.
With the concurrence of the manufacturer, it is permitted to increase the above time duration.
( K  D9 o; n  K0 b' GFor large equipment where it is impractical to condition a complete ENCLOSURE, it is permitted
to use a portion of the ENCLOSURE representative of the complete assembly with regard to
! m. W4 D8 o; @! f4 r5 j) I1 ythickness and shape, including any mechanical support members.
1 X& a+ x7 g. vNOTE Relative humidity need not be maintained at a specific value during this test.
7 T. L! `) I2 D3 d! {: s/ e$ n6 X5 HIf the above test is conducted, the compliance criteria of 4.2.1 apply.

frankzhou

通俗点就是拉电源线的卡口，看是不是很耐用！！我们公司是这样测 的~

ferry

有沒有辦法對應力進行計算?
比如說材質不同,它的應力系數是多少等等....
- }; C6 R: n7 C* l1 a5 D/ Q能否請一并提供此類資料,謝謝..

caballo3157

可以查材料手册和参看材料力学等书籍

awen

对于电源线，我们在电线和线芯上打上标记，再用156N的力拉1分钟，再根据标记的位置来确定电源线与线夹相对移动的距离和线芯与电源线外皮相对移动的距离来判断电源线有没有受到应力。