|
The temperature test is to be performed in the following manner:- x/ j( {: Q& z
a) Metal cutting-mixing blade (S-blade) –
) W3 T/ W* T. V6 ~9 i% R) [i) For a food processor supplied with mixing attachments or instructions for mixing
! M1 ~* I/ @7 y5 a5 |$ qdough, the cutting-mixing blade is to be installed in the appliance as intended. The
0 Y/ y4 W( i) I! x6 a& z! Oappliance is to be operated for 4 cycles of operation. Each cycle of operation is to- Y/ g* v( I7 W, O3 a# \9 F* W' s
consist of 3 minutes on followed by a 1 minute OFF period. The bowl is to be filled with3 h4 f+ u3 n7 W# i2 y& s7 x
dry 50 – 80 core sand, which is to be changed and replaced with fresh sand after each
# K4 H( n7 s- b5 ]cycle to a level which causes an input (wattage) to the appliance equal to the average
, a" K2 ^1 U* p Vinput noted in the input test when processing the food which resulted in the highest# U0 Y' w1 C+ X% A: \. A
input. The amount of sand employed is not to exceed the maximum capacity of (total3 \ s( ]4 Z* @) \7 }, g; q8 P
amount containable by) the bowl.
4 C" M! Z0 w) j$ Vii) For a food processor not intended for mixing dough, the temperature test is to be
. F4 d4 s+ P. t* k& j, u2 qperformed with the appliance operating for 10 cycles. Each cycle of operation is to# m; X/ I0 P4 X
consist of an on time of 15 seconds or the time specified in the manufacturer’s- n0 J2 k! x- A
instructions, whichever is greater, followed by a 1 minute OFF period. The foodprocessor is to be filled with the type of food which resulted in the highest input during& R2 r1 @; R0 m( M
the input test described in 36.19.1, in the quantities recommended in the Instruction
- v; \1 m* d- u3 C- ]% r( zManual./ Z. W( n; t$ F* _. b
b) Slicing disc, shredding disc, or both – The disc to be tested is to be installed in the food
# o% C4 Z0 x, S( w, Y& Bprocessor bowl as intended. The appliance is then to be operated for 4 cycles of operation,
# O# l' U- E# b% C! uslicing or shredding the food that caused the highest input to the appliance as noted during the k, h5 b; ]% T3 Q
input test. During each cycle of operation the bowl is to be filled to its maximum capacity or to a
+ Y" ^/ e' l7 L8 G- a" nmaximum-fill indicator, if provided, with the food being processed, followed by a 1 minute OFF# v3 ~2 K* b7 ~# o) g
period. The force applied when pushing food through the food processor is to be 1.1 lbf (5 N).2 [0 K# `8 M( U" l( i( ~3 |
这写的这么清楚了,
# E; }" }' @& B* w7 m- t3 o刀头是S型的,一般作为搅拌和切断功能的金属刀片。
3 \+ C, T( s+ P5 c5 ^# K% |1带搅拌面粉功能的,做4个循环,3分钟开一分钟关为一个循环。4 M; a- B8 l1 E7 [; A& m8 b! p
2不带搅拌面粉功能的,做10个循环,15秒开或按说明书时间开(取大值)一分钟关为一个循环。
2 {; o$ V, Q% ?7 z. T% p' H$ u圆形光盘状旋转切削的刀片
3 h- l' s8 J1 @ l0 V) R做4个循环,以最大进给量,关1分钟为一个循环。: M; j9 c* I5 d3 m% X; f
1 k. v6 ~" ~. ]& I T' R0 R
温升测试都是按实际使用情况模拟的,如果说明书和标准的循环时间不一致,一般都会采用说明书上的最为合理。 |
|