UL医疗插头，张力缓冲测试一直过不了

ydqshy

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

哎，怎么个问题呢，搞不懂啊，有大神吗

jjlamshushushu

UL医疗插头，张力缓冲测试?测试规范呢？

CHENGFEGO

jjlamshushushu 发表于 2014-5-30 18:05
  P. J; N$ j, S7 o* N, zUL医疗插头，张力缓冲测试?测试规范呢？

& r+ y6 y2 w( y% I2 l109 Strain Relief Tests
" r$ y/ e: p# Q4 ~  H, l109.1 General
9 ?0 A) A' J( s; c- Z109.1.1 After being subjected to the strain relief tests described in this section, there shall not be any
displacement of the conductors, conductor insulation, or outer jacket of the flexible cord exceeding 1/32
inch (0.8 mm). There shall not be any cuts, rips, or tears in the cord insulation nor any breakage of the
; ~4 ^, C3 X; z8 o- }attachment plug that could adversely affect the enclosure of live parts, strain relief, or grounding path
- ^, H# [% r+ u9 Qintegrity.
" q+ t2 |0 _6 k. L8 {: R6 a109.2 Method A – Static pull
109.2.1 Each of six representative attachment plugs molded onto flexible cord, without the conductors
terminated to the blades or grounding pin, shall be subjected to a gradually applied pull of 30 lbf (133 N)
' m  R" M7 ?( Q2 ]' sto the free end of the cord while the attachment plug is securely supported. The force shall be applied for
" f, Q2 K+ u) H* c1 minute in a direction perpendicular to the plane of cord entry.
  i' K+ X  x; k' `109.3 Method B – Rotary pull
109.3.1 Each of six representative attachment plugs molded onto flexible cord, without the conductors
. d) F1 v; G. i, Kterminated to the blades or grounding pin, shall be subjected to a rotary cord motion while a force of 10
lbf (44.5 N) is applied for 2 hours. The cord is to be rotated at a rate of approximately 9 r/min in a 3 inch
diameter (76 mm) circle at a point 6 inches (152 mm) below the cord exit with the attachment plug rigidly
mounted. (Note – This test is conveniently done with UL secureness test apparatus described in the
Standard for Wire Connectors and Soldering Lugs for Use With Copper Conductors, UL 486A, or in the
7 J* K- p: R: [. D- d) o( u- g, ~' HStandard for Wire Connectors for Use With Aluminum Conductors, UL 486B.)

ydqshy

jjlamshushushu 发表于 2014-5-30 18:05
UL医疗插头，张力缓冲测试?测试规范呢？

8 G( Z1 V8 j, `1 t& M109页的，我们是铜丝位移过不了