胶水固定是一种可以被接受的固定方式么?

ahead

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

在做22章结构的测试的时候,有做50,30N的推拉力测试,如果测试中能被拉出来然后触及到带电体,如果用胶水做固定然后用同样的拉力能够通过测试,请问这样的方式可以接收么?谢谢

lynn305

请说明标准, 不然大家没法回答呀?
22.3 A new sample of the appliance is firmly held so that the retention of the pins is not affected.
3 u4 D8 N) G3 n) e5 i+ T5 ]9 DThe appliance is placed in a heating cabinet for 1 h at a temperature of 70 °C ± 2 °C.
The appliance is then removed from the heating cabinet and a pull force of 50 N is
immediately applied for 1 min to each pin along their longitudinal axes.

若是IEC60335的话, 你是把PIN拉出来了, 还是把整个SOCKET拉出来了?
9 j, X( O" H& f+ y: J- @/ ?- S' JSOCKET和PIN都是不能用胶水固定的, 因为在SOCKET的零件认证中, 已认证了相应的固定方式, 不包括用胶水.

嘻嘻

一般是不接受的，只是看自己是否可以取巧了

fasten

22.11 Non-detachable parts that protect against access to live parts, moisture or contact
with moving parts shall be fixed in a reliable manner and withstand the mechanical stress
1 c) r- |$ _/ A. Koccurring during normal use. Snap-in devices used for fixing such parts shall have an obvious
locked position. The fixing properties of snap-in devices used in parts that are likely to be
( R# l  g0 N+ K  b' m3 dremoved during installation or servicing shall be reliable.
' f) @4 S! \2 w# O' V; N# c& Q
$ g: I* k1 L- ?" u不管是美系标准还是欧系标准，用粘接（如胶水）做固定不是reliable的连接，所以是不可以接受的！

ahead

是21.11
+ W9 ]* l" v' n2 q$ s: t* @22.11 Non-detachable parts that protect against access to live parts, moisture or contact
5 }9 B1 O' `; A4 Iwith moving parts shall be fixed in a reliable manner and withstand the mechanical stress
5 a4 P; i$ l1 G6 P" G. Poccurring during normal use. Snap-in devices used for fixing such parts shall have an obvious
locked position. The fixing properties of snap-in devices used in parts that are likely to be
# M8 v- K  @+ r1 E  g( x/ bremoved during installation or servicing shall be reliable.
& U( `5 Z8 K  H5 lCompliance is checked by the following tests.
9 i4 c- ~1 n) G8 f! u  x; J8 v. M2 wParts that are likely to be removed during installation or servicing are disassembled and
assembled 10 times before the test is carried out.
9 L2 P5 H2 v. O, QNOTE Servicing includes replacement of the supply cord.
  \% a$ r7 l4 ], J# M7 PThe test is carried out at room temperature. However, if compliance may be affected by the
1 ?: [3 j+ O# R! q6 ]2 etemperature of the appliance, the test is also carried out immediately after it has been
7 m, E$ c* l  ?2 j/ e1 _5 Aoperated under the conditions specified in clause 11.
The test is applied to all parts that are likely to be detachable whether or not they are fixed by
; z- E$ I$ T! ]0 Q- s. @2 Lscrews, rivets or similar parts.
force is applied without jerks for 10 s in the most unfavourable direction to parts likely to be
weak. The force is as follows:
– push force, 50 N;
/ C& m. @) w. r) r– pull force:
if the shape of the part is such that the fingertips cannot easily slip off, 50 N;
; v, T. U  A' n6 z/ b0 N. |) Y if the projection of the part that is gripped is less than 10 mm in the direction of
8 e" t4 i1 s7 y- X4 }, z8 P- d1 Uremoval, 30 N.
& h: g7 V: h, s) k% GThe push force is applied by test probe 11 of IEC 61032.
% T( ]; e; W3 l6 E: Y/ ^+ e' M. M0 K
# B& S$ p0 \5 C* B8 k
但是标准上面哪个地方说了不能用胶水么?
0 b4 k. H5 _. o8 x谢谢

hncjy365

60335-1  22.12   注释:自固性树脂以外的密封剂和类似材料,不被认为对防止松脱是足够的.