|
|
FDA 已采认 IEC 60601-1-4:2000 标准, (Effective Date: 07/31/2008)
3 Y) D; v% t4 X" v3 NIEC 60601-1-4:2000, Medical electrical equipment - Part 1: General requirements for safety - 4 - Collateral standard: Programmable electrical medical systems, edition 1.1. (General) ,! D; ^" t1 E- I+ H; ?
8 ^6 O7 m9 f) k- B* \! N但也提出若干要求与但书:* [+ T$ y" ~% q+ V
Extent of Recognition:
/ T$ l7 x4 Q4 R" B: VIEC 60601-1-4 specifies basic requirements for the process by which programmable electrical medical systems are designed. The standard provides basic risk management processes that may be applied to the development and qualification of programmable electrical medical systems.
( K: I! [8 T5 R6 l% a. _7 W& i& v# K; \! D
Portions of this standard related to risk estimation do not appropriately address failures of a systematic nature (hardware design failures and all software failures). The risk associated with a random failure is assessed by considering both the severity of the hazard caused by the failure and the rate of its occurrence. Unlike for random failure, however, the probability or likelihood of systematic failure is impossible to predict. Consequently, hazards associated with risk-related functions subject to systematic failure should be managed based on the severity of the hazard resulting from failure and the assumption that the failure will occur. Hazard management should focus on the mitigation or elimination of hazards that adversely affect patient safety. Hazard analysis should begin with the identification of system requirements and continue throughout the product life cycle. Where applicable, design features should be incorporated that prevent single component failures from adversely affecting patient safety.2 V! D% E! X1 Y3 Y4 }& ?7 V
; A5 k9 ~6 w) N$ MWhen reviewing programmable electrical medical systems, reviewers may request documentation from the risk management file described in IEC 60601-1-4, for example, system requirement specifications, hazard analysis, hazard mitigation features, and validation reports. In addition, because conformity to the IEC 60601-1-4 standard may not be sufficient for purposes of demonstrating safety for regulatory submissions, manufacturers should be encouraged to contact the appropriate ODE reviewing group to determine the applicability of this standard for a specific medical device.
0 r9 Q f5 j' v5 ]: v0 ?2 ZRelated CFR Citations and Product Codes:) Y! D9 G- W7 D
$ t5 ?( b6 ~* ^5 W
Other:
9 X1 T, r& L( p( c" XThis standard is relevant for all programmable electrical medical systems/ Y. ]; ~1 p: e. ]! a
! Z% y5 Y: Q+ A, v8 kRelevant Guidance:
8 N. f0 o, S s+ ?5 c: [- G" f8 M$ hGuidance for Industry and FDA Staff - Guidance for the Content of Pre-market Submissions for Software Contained in Medical Devices, May 11, 2005
( v* p6 y9 E2 f3 m) v
, [+ l9 X9 S/ C' N1 L7 T' v9 WGeneral Principles of Software Validation; Final Guidance for Industry and FDA Staff, January 11, 2002% P6 b. w1 ]5 g1 |8 e3 G9 ^
" `, x, o) u4 N8 A3 W bGuidance for Industry, FDA Reviewers and Compliance on Off-The-Shelf Software Use in Medical Devices; Final, September 9, 1999 |
|
/1 
|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网
( 粤ICP13023453-10 ) 
窥视卡
雷达卡
发表于 2008-10-22 09:47
显身卡
发表于 2008-10-23 21:06