产品的CCN和UL file number是强制要印刷在产品上吗？

Andy.Yang

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

jsspace 发表于 2014-10-10 15:33
看了一下MY home相关的文件，似乎没有要求印刷UL file number，但是我看到的产品都应刷了

2 n/ w7 _; `6 VTell me your file NO. I may help to check it...

jsspace

Andy.Yang 发表于 2014-10-10 15:50
, b% e  H% Z" v, P/ Z8 c( cTell me your file NO. I may help to check it...

E326276

Andy.Yang

jsspace 发表于 2014-10-10 15:56
E326276

For listing mark products, I can not check the marking requirements through UL website, but for recognized products under this file, the requirements are as below:
  s6 D/ j) d1 U) V& WMarking: Company name, model designation, and Recognized Component Mark "RU"
So, I assume for the listing product, only the company name is indicated in your FUS procedure, in this case, suggest you to ask UL to modify the FUS procedure which can allow you to use the File No. to indicate the company name, in order to avoid any VN issue during the factory audit, but for some auditors, this is not an issue, and VN will be not issued accordingly, it depends...

jsspace

Andy.Yang 发表于 2014-10-10 16:05
8 x# _/ L# u) O9 B, g7 h) t/ tFor listing mark products, I can not check the marking requirements through UL website, but for re ...

" G+ W' V* K8 p2 xmy home上有“FUS procedure" 吗

Andy.Yang

jsspace 发表于 2014-10-10 15:56
E326276

' l  }5 N% D6 {2 ^* G8 ], A5 R' _I just checked our UL files, and found the marking requirements are indicated in the detailed sections, you may need to check the detailed section, not Sec. G for the marking requirments, to name an example as below:
" b+ U( }5 m" K/ S2 [- f2 _Markings - Products shall be marked with Listee's name, model number, contact rating code and enclosure environmental rating.  The letters for the marking "4X Indoor Use Only" shall be 5/32 in. (4.0 mm) high minimum.  In addition, installation instructions provided with each device shall specify:  the maximum operating ambient temperature, voltage and current ratings for contact rating codes.

jsspace

Andy.Yang 发表于 2014-10-10 16:18
I just checked our UL files, and found the marking requirements are indicated in the detailed sect ...

Sec. G也有marking的要求啊，以下是我在Sec. G摘录出来的：
3 O& A% U' y" K' W" |MARKINGS:
1 f$ j, N. U8 r  \, ~
3 k, x" E/ t* x! f! KEach device shall be legibly and permanently marked with the Listee's name, trade name or trademark (if authorized), and the device model number.

' i  i9 B, d- j- w+ h) l4 UEach Lamp Adapter shall be marked with a rating for each replacement lamp(s) in watts, unless otherwise noted in each individual section.

+ O9 r' \2 ~; K  q1 m, m: j1 |" iThe electrical rating markings provided on the device shall include the input voltage, frequency, wattage and current.  However, one or more of the electrical ratings may be omitted as follows:
" ]' _" c& X& Y5 w8 [
( I- l2 i8 q# s! H/ t- ?% `-        The wattage rating need not be marked on a Lamp Adapter.
3 b+ ~) S# e( a. G8 Q  d+ K* w7 W
-        The current value may be omitted if the product is marked with the input wattage and the power factor is 0.9 or greater, as may be indicated in each individual section.

A date code or other dating period of manufacturing, not exceeding any three consecutive months, shall be provided and may appear on the surface of the device or the lamp base screw shell.  The date code may be abbreviated; or may be in a nationally accepted conventional code or in a code affirmed by the manufacturer, if the code:
$ D4 ?; v7 v# [, T% e% m1 H0 z
a)        Does not repeat in less than 10 years, and
* f( w" X* \1 |$ w
5 S( l0 m* v/ gb)        Does not require reference to the production records of the manufacturer to determine when the product was manufactured.
. L2 U  Y, a/ r1 s4 {1 a

Andy.Yang

jsspace 发表于 2014-10-10 16:18
my home上有“FUS procedure" 吗

Perhaps, you can select "my UL report/CDA", then under the sub. No, you can directly check the e-copy of the fus procedure, normally, it covers: authorization page, listing mark data page, section General, Appendix, Index page, Section 1,2,3...(which I mentioned the detailed sections).

: |7 e! D: h+ v0 D9 ISo you'd better to check the detailed sections to find out the marking requiremnts...

Andy.Yang

jsspace 发表于 2014-10-10 16:20
Sec. G也有marking的要求啊，以下是我在Sec. G摘录出来的：
MARKINGS:

Yep, that is...
/ I# l9 w8 E( O! F2 C% M% }So you need to check both Sec. G and detailed sections to summarize all marking requirements, then indicate all those accordingly....

7 w: F7 E' m' z! d4 dNormally, for most of the factory auditors, they do like to issue VN related with the markings, very easy...