|
| DSH 590+ k2 x: ?3 K: M, F: z/ b; o7 J8 v
( v7 }, G+ ~1 d; F) s* ]
| Rule for creepage across grooves and similar surface discontinuities, u% v7 e4 A4 J3 ]+ V# h3 B* z2 y
| IEC60664-1: 1992 cl. 4.2 IEC60335-1: 1991 Annex E IEC60335-1: 2001 Cl. 29 IEC60730-1: 1999 Annex B IEC60950: 1999 Annex F IEC60950-1: 2001 Annex F IEC60065: 2005 Annex E IEC61010-1: 2002 Annex C IEC60601-1: 1988 Notes Figs 39-47 IEC61558-1: 1988 Annex A IEC61058-1: 2000 Annex A IEC60598-1: 2003 - IEC60745-1: 2001 Annex A IEC61008-1: 2002 Annex B IEC60947-1: 2004 Annex G
1 A. w8 d) J: L. Q | 60335-1(ed.4) & 61058-1(ed.3) & 60598-1(ed.6) & 61010-1(ed.2) & 60950-1(ed.1) & 60947-1(ed.4) & 61008-1(ed.2);am1 & 60065(ed.7);am1 & 60664-1(ed.1)- U/ v5 y, x4 U* T. [, y4 v
| 7 e. G# y# K9 \2 @
Standard: IEC 60664-1/1992+ M' a2 e! A8 y
IEC 60335-1/2001
& P3 c: d4 ?0 Y! X: dIEC 61010-1/2002
# {6 t* a% ^' e# b iIEC 61058-1/20002 E+ u% p* C7 F4 j" f) k
IEC 61008-1/2002
8 G3 b% I( V) [5 a$ W, r1 aIEC 60947-1/20045 x, [1 a8 X9 b1 e; a( `$ L
IEC 60598-1/2003
$ @, u0 a7 \* o; p1 F5 LIEC 60065/2005
0 U2 n0 X- p% u' f' j6 YIEC 60950-1/2001$ I" C" M8 s0 S
Sub clause:
7 c" l, U, r6 h* Z' v4 gSee Table below
+ y+ C+ j6 J1 [- KDSH N°: 590! d/ J2 n6 A8 ^0 j
Page: 1(1)0 P) I" L0 e0 ~) e d
Subject: Rule for creepage across* U+ z. ~7 F' G* t1 ~; D. D
grooves and similar4 }- @" W, a, M2 u
surface discontinuities; L0 {9 R% u0 H+ I- [9 p. T i" x
Key words:
n0 ?- R$ i7 s5 v5 u( t( i# W- Creepage/ e& |; D9 k# l
- Grooves. A: X3 R0 l& }) |" H" b# k$ T
- Conducting path
. J# i, m1 U/ c- Shortest distance% m4 \# J3 k6 t3 S6 n
- Through air
% ]! f0 {) ~7 pDecision approved; ` r9 H: f F; e) o
by the CTL during
0 t) H. e$ }0 r/ y6 i) Q s% X9 Nits 43rd meeting in) i' W5 x9 t. @
Johannesburg
0 ?! ^8 {5 C) g, _Question: As can be seen from examples 2 and 6 of IEC 60664-1 sub clause 4.2 corners
* a+ |) {1 { ^+ ]with angles greater or equal than 90 degrees are not bridged. IEC 60664-1 does
3 l, r9 G, C1 S7 wnot contain specific information at which angle less than 90 degrees bridging
: B8 j& d& J$ b9 T% dshall be applied. Some of the above mentioned standards specify that bridging
9 A: ^1 H" v8 f, @0 a8 jshall be applied for angles less than 80 degrees.
& S0 S+ i" e8 y" Y6 XCan this 80 degree rule be applied in general for all standards?+ P2 ]$ d' k# g# I
Decision: Yes. The 80 degree rule shall be applied in general for all standards.
! A% c9 i# q. B$ U8 S0 n* S; f8 i5 I `
' ~1 D% I+ |3 y; [
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有帐号?注册安规
x
|