|
| DSH 754; \7 Y( H0 \! R! |. e5 H2 f! r
| Screws, Creepage distance and clearance
, [+ G3 @* A5 b7 I3 e | 21.19
1 r6 c. k- g! W/ a; q | 60745-1(ed.4)
* o4 H# S1 a0 w& O5 u1 X$ H |
2 k4 A, X) \% W8 q5 z6 g" K8 O. DStandard(s):
' ^9 d8 Z! U- y' c& y& K: XIEC 60745-1:2006
' k0 e+ S5 x( D- B4 k7 k& LSub-clause(s): S1 o( B4 J7 c& Q. O
21.19
' K4 I) h0 {4 U7 hNo. Year! j' j9 B6 [- M$ D# ?0 e: j8 x9 {5 }
DSH& _' U9 e( a2 G; d3 F* u; Y
754" u" f9 V. Z$ n& \
2010
& @# h C: N& j; s5 q: ]# vCategory: TOOL Developed by: ETF 1
5 U& z* U/ }6 y7 A) F9 eSubject:/ |0 j6 D0 r; J) L1 E9 }
Screws, Creepage, ]9 P" F# j7 o6 h' h. F, N: Y7 z
distance and clearance9 a7 z+ a6 c' O6 q* @" d& m: p
Key words:
7 w0 p# J3 D" k+ K n% @$ ]- Screws
0 U# ^ P# U q; v- force
. l L+ m9 b' }+ J1 L- Creepage distance and" d& p' e' _; W4 r/ a# R
clearance
' ^" B/ n; S9 J7 c0 nApproved at the 2010 CTL
3 y! ]: E7 o6 c; M6 h( c$ D2 |Plenary Meeting$ E' @3 Q+ E3 y& e7 B
Question:
% r% ]' q. E2 ^% a! i1)4 p" _: F @9 }- s- f
“Tools shall be so designed that the protection against electric shock is not affected when
- a. T& k9 ]( l4 o9 P) \screws intended for replacement from the outside during routine servicing are replaced by
7 w9 c3 O( E5 {screws having a greater length.”+ x/ u3 S k# r+ Z0 R, m- s8 x5 ^
What screw should be used? Only the screws from equipment under test or any other
' K8 |* m7 C* ^# M$ f2 g- gpossible screw?9 J, f: B8 d0 Y3 E. p
2)
- w, J1 V% h: Q: b“Compliance is checked by inserting longer screws, without appreciable force, after which
$ g. [" a% t/ K' pcreepage distances and clearances between live parts and accessible metal parts shall not) W+ V: ]/ K( w' j i2 z
have been reduced below the values specified in 28.1”
9 B% y8 p! z8 ~ y* s I& a/ SWhat force is to be applied?
, V5 s& S$ u: i R& [ f5 ^Decision:2 ~7 C# Y' V5 B9 ~5 U4 C
1)
p9 p. x |' i7 i' F1 w, ZThe screw originally used on the equipment and any other longer screw that can be found. U0 y! K* ~7 A: F7 u
on the equipment is to be used.
% r: N2 n5 W, _2)
0 ?3 B# d4 i @& V: aThe force values in Table 9 shall be applied.( w0 q' U( W5 _- R4 ]! Q" [
% p1 J F. N/ c4 K$ l; ~
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册安规
x
|