安规网

 找回密码
 注册安规
安规论坛 | 仪器设备 | 求职招聘 | 国家标准 公告 | 教程 | 家电 | 灯具 | 环保 | ITAV 签到 充值 在线 打卡 设备 好友| 帖子| 空间| 日志| 相册
IP淋雨机 | 证书查询 | 规范下载 | 资质查询 招聘 | 考试 | 线缆 | 玩具 | 标准 | 综 合 红包 邮箱 打卡 工资 禁言 分享| 记录| 道具| 勋章| 任务
水平垂直燃烧机 | 针焰 | 灼热丝 | 漏电起痕
IP防水防尘设备|拉力机|恒温恒湿|标准试验指
灯头量规|插头量规|静风烤箱|电池设备|球压
万年历 | 距元旦节还有
自2007年5月10日,安规网已运行
IP淋雨设备| 恒温恒湿箱| 拉力机| 医疗检测设备沙特Saber 埃及COI 中东GCC|CoC直接发证机构水平垂直燃烧机|灼热丝|针焰试验机|漏电起痕试验机
灯头量规|试验指|插头插座量规|灯具检测设备耐划痕试验机|可程式恒温恒湿试验箱 | 耦合器设备广东安规-原厂生产-满足标准-审核无忧
查看: 858|回复: 0

[MEAS] DSH 323 Clearances and Creepage distances

[复制链接]
发表于 2012-9-19 14:15 | 显示全部楼层 |阅读模式
广东安规检测
有限公司提供:

5 n8 j& L+ M) i2 L, ]* B/ V$ N- s" A" I5 m8 C4 ]) c4 u( j3 ]
DSH 3233 B' b/ [3 h' g$ U0 z
Clearances and Creepage distances* s. Z+ f; g4 \( v: E
6.7
  k- K- I" {1 p$ N# d, g; R
61010-1(ed.1);am1;am2
) a# \" r. X. Y, c/ @
) t4 [- ~( A; @" I0 K

2 g2 v3 H5 i3 k* O! [1 aStandard:
' ]) p+ e' z, ~# e, N7 mIEC 61010-1:1990+A1:1992+A2:1995
/ _+ o9 Z5 F: X1 f7 SSub clause:) l. c& z) K5 D3 G+ M0 p2 j
6.7: b1 V3 L) L# k
Sheet n. 323# @( S' g$ u( V4 y1 J: V
Page 1(1)
7 ?' |2 R9 c- g" VSubject:; w7 ]( ~- H' t& G- [3 g  O
Clearances and Creepage distances
% u0 _, `4 Z* k5 S0 NKey words:
/ s) T( `+ M0 [- Clearance3 ?0 I  C+ f3 O2 h7 C& ~1 o
- Creepage
, w$ v% I' n9 ~% i; P5 l9 n- Pulses
+ u  s/ k% y& @: m+ Y! v' AProvisional decision taken by ETF3 and confirmed by CTL at its 38th meeting, in Toronto
4 t) ]( j* x4 Q  h7 e, N0 iQuestion:
; c/ \" R( i9 C2 C8 ADo creepage and clearance distances have to be calculated from the peak value of voltage spikes occurring between parts even when the parts in question are subject only to very short duration pulses occurring at defined times e.g. switch on?
4 x9 D% h) Z! b- {* K; fDecision:" \+ t; U$ Y( c" ?8 n
Clearance distances must be compliant with the value for the highest voltage present on the parts concerned, creepages distances must not be less than clearance values, therefore no reduction in values is allowed.% ~1 F1 e- G: \- s; G
Where the distances are less than required values they should be shorted out and measurements carried out in accordance with Clause 6.3.2. ‘Values in single fault condition’ to determine whether a hazard exists. If no hazard exists then the device is compliant with the requirement.
1 J! [: E- q7 vExplanation:: E% x( i) W9 V4 f
Clearances are liable to break down under excessive voltage and therefore cannot be reduced from the stated values. However for very short duration pulses the energy transmitted to accessible parts may be within the limit allowed by IEC61010-1 and the clearance is not then essential as a means of protective isolation.
+ B' G9 X7 D3 V' h5 [7 a) ?2 N2 b( A4 L( i" _: Y, D7 G2 Y
! }+ ]2 `) J1 e) h
' y3 |0 H6 N8 {- Z

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?注册安规

x
您需要登录后才可以回帖 登录 | 注册安规

本版积分规则

关闭

安规网为您推荐上一条 /1 下一条

QQ|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网 ( 粤ICP13023453-10 )

GMT+8, 2024-12-24 22:18 , Processed in 0.073819 second(s), 23 queries .

Powered by Discuz! X3.4

© 2001-2023 Discuz! Team.

快速回复 返回顶部 返回列表