PDSH 997 Open circuit voltage measurements

小米

广东安规检测
有限公司提供：

小型摆管淋雨试验机

IPX5X6X7喷水试验机

1000L恒温恒湿箱

各种试验指现货

可程式恒温恒湿试验箱

水平垂直燃烧机

自动卷线器试验机

耐划痕试验机

各种灯头量规现货

灼热丝试验机现货

GB1002插头量规

IPX1-X7淋雨现货

IEC61347/UL935镇流器热试验箱

灯具防风罩

IK冲击试验机

UL498插头插座量规

VDE0620插头插座量规

稳定性试验台

家电温升测试角

针焰试验机现货

热电偶焊机现货

家电125mm试验指

E12灯头量规

无绳壶无绳电熨斗插拔寿命试验机

IEC60335试验指甲

PDSH 997 ! u9 Y1 T8 ]0 R* J3 u

Open circuit voltage measurements - a/ C$ m+ `' c4 }

Annex A.4 – Annex A.4.1

60929(ed.2) & 60929(ed.3) & 60929(ed.4) 8 a  T3 r6 P- a( o

Standard(s):
IEC 60929 All editions
4 A; J: k$ }# F/ MSubclause(s):
Annex A.4 – Annex A.4.1
No. Year PDSH 0997 2010
: u. K, u! c; L' V  RCategory: LITE Developed by: ETF5 OSM/LUM
: d5 C5 f1 k. z0 H6 S( ?) LSubject:
# L5 ^, g0 m7 \6 ^0 m2 uOpen circuit voltage measurements
Key words:
- Instructions
/ `$ D) K5 r) @1 ~. |2 p/ `7 b- Lamp manufacturer
/ q% K+ m0 U; [4 `# A2 P- j- Preheating
To be approved at the 49th CTL Plenary Meeting, in 2012
Question:
For the measurement of the open circuit voltage on a ballast with two lamps in series:
1) Is it correct to take the measurements across both lamps, not one at the time, because the
' p/ P9 u$ d: R3 u+ W2 Ctotal voltage of the two lamps in series has to be measured?
2) If the answer to 1) is yes, does it make sense to take the value referred in the data sheet to
one lamp as the limit value of the open circuit voltage during preheating (measured across
two lamps)?
0 w& a( ?% \$ u7 A  ^3) During ignition, the open circuit voltage shall be greater than the minimum voltage
. K4 I9 i$ [' @" y4 t0 ~specified in the lamp data sheet for two lamps in series. Is there any data sheet that specifies
2 z* a% r- m0 j9 b1 s- b$ ^( n6 Cthe minimum voltage for two lamps in series or has the minimum value for one lamp to be
: P( g9 s) D( h% ^used for two lamps in series?
+ K; I/ S! c/ a& T. UDecision:
1) Yes.
& {3 S4 M4 \3 N: f+ }2) Yes, if the value is indicated in the data sheet or in the instructions of the lamp manufacturer.
8 e1 H- t- H1 z  p& O+ @+ i% uOtherwise, twice the value for one lamp can be used.
" u) m! R  I( Z) a: S) C  d: @3) The minimum voltage must be less than the maximum value of one lamp during preheating and at least
the value of two lamps after preheating.
! P$ w/ s% P6 ~7 o8 ~. j1 e