|
The temperature test is to be performed in the following manner:; P; R7 U2 R, t+ B2 [* a
a) Metal cutting-mixing blade (S-blade) –
3 a# b: F2 S& s* B* L. E* ii) For a food processor supplied with mixing attachments or instructions for mixing
2 V; K$ c3 K3 Ydough, the cutting-mixing blade is to be installed in the appliance as intended. The, {9 \% f- e2 J7 d1 a
appliance is to be operated for 4 cycles of operation. Each cycle of operation is to
, M! r" V1 r, Y/ W: `; q% Nconsist of 3 minutes on followed by a 1 minute OFF period. The bowl is to be filled with
& S2 y ?# R% }& J7 k0 [dry 50 – 80 core sand, which is to be changed and replaced with fresh sand after each
' A4 ^# M/ p6 Vcycle to a level which causes an input (wattage) to the appliance equal to the average
6 x; i6 `& V; }' Ainput noted in the input test when processing the food which resulted in the highest
8 G$ s8 j w# v" V1 Ninput. The amount of sand employed is not to exceed the maximum capacity of (total
' r/ g* i0 K" y0 Q0 q8 r9 T$ Gamount containable by) the bowl.# r- ?* V/ z3 G Q& }, {. Z
ii) For a food processor not intended for mixing dough, the temperature test is to be4 L& `- e/ g2 ~6 e# K. ~2 e
performed with the appliance operating for 10 cycles. Each cycle of operation is to# \7 l! v6 B* {" a9 ~0 k1 b
consist of an on time of 15 seconds or the time specified in the manufacturer’s- t5 x& C9 N' s$ B" d `: C
instructions, whichever is greater, followed by a 1 minute OFF period. The foodprocessor is to be filled with the type of food which resulted in the highest input during# e4 H6 S( j9 u1 G* I
the input test described in 36.19.1, in the quantities recommended in the Instruction4 o# Z4 d/ b+ ]' y
Manual.
4 b: X8 @6 w% V" @7 ]5 \b) Slicing disc, shredding disc, or both – The disc to be tested is to be installed in the food
# n5 ~8 T: w" }# `processor bowl as intended. The appliance is then to be operated for 4 cycles of operation,
6 J- E- M( S7 p+ k7 p4 q4 p+ G, vslicing or shredding the food that caused the highest input to the appliance as noted during the
( G$ c p4 \1 ^, x1 c" }input test. During each cycle of operation the bowl is to be filled to its maximum capacity or to a
6 `3 ?- x3 n2 J+ K$ [" E1 N: tmaximum-fill indicator, if provided, with the food being processed, followed by a 1 minute OFF2 _% ]' k. @. {4 b1 F& H" a
period. The force applied when pushing food through the food processor is to be 1.1 lbf (5 N).
9 T- T; B/ M/ L/ {这写的这么清楚了,) q' t6 G8 f! l' N( n- \
刀头是S型的,一般作为搅拌和切断功能的金属刀片。
0 V( b' T: Z+ G/ W+ n1带搅拌面粉功能的,做4个循环,3分钟开一分钟关为一个循环。: @: [% `- q1 D$ a! w+ E# A
2不带搅拌面粉功能的,做10个循环,15秒开或按说明书时间开(取大值)一分钟关为一个循环。
7 z. X8 o" Z7 |5 F% | H8 h圆形光盘状旋转切削的刀片
* }2 C* q4 p4 ^6 y5 W做4个循环,以最大进给量,关1分钟为一个循环。 A, x+ }6 }1 s4 M/ b P% c
4 c$ Q+ x9 T' Q* y3 a
温升测试都是按实际使用情况模拟的,如果说明书和标准的循环时间不一致,一般都会采用说明书上的最为合理。 |
|