安规网

 找回密码
 注册安规
安规论坛 | 仪器设备 | 求职招聘 | 国家标准 公告 | 教程 | 家电 | 灯具 | 环保 | ITAV 签到 充值 在线 打卡 设备 好友| 帖子| 空间| 日志| 相册
IP淋雨机 | 证书查询 | 规范下载 | 资质查询 招聘 | 考试 | 线缆 | 玩具 | 标准 | 综 合 红包 邮箱 打卡 工资 禁言 分享| 记录| 道具| 勋章| 任务
水平垂直燃烧机 | 针焰 | 灼热丝 | 漏电起痕
IP防水防尘设备|拉力机|恒温恒湿|标准试验指
灯头量规|插头量规|静风烤箱|电池设备|球压
万年历 | 距国庆节还有
自2007年5月10日,安规网已运行
IP淋雨设备| 恒温恒湿箱| 拉力机| 医疗检测设备沙特Saber 埃及COI 中东GCC|CoC直接发证机构水平垂直燃烧机|灼热丝|针焰试验机|漏电起痕试验机
灯头量规|试验指|插头插座量规|灯具检测设备耐划痕试验机|可程式恒温恒湿试验箱 | 耦合器设备广东安规-原厂生产-满足标准-审核无忧
查看: 1996|回复: 7
打印 上一主题 下一主题

[美洲标准产品] UL产品的电线警告标签(求助)

[复制链接]
跳转到指定楼层
楼主
发表于 2010-1-18 14:17 | 只看该作者 回帖奖励 |倒序浏览 |阅读模式
广东安规检测
有限公司提供:
我公司有款取暖器 送UL做认证时 要求在电源线上加警告语标签 哪位DX帮帮忙 应该做成什么规格 内容有什么要求吗?在线等
沙发
发表于 2010-1-18 14:38 | 只看该作者
UL817 PROCEDURE SECTION GENERAL 要求:
, B, @) d4 K! H9 O    美規US Type 電源線AC Cord, 根據UL817規定從去年2006.06.24 就開始要求, 如下文及附件:) s$ W; r. y7 I  p

# h4 ~7 S6 z) Q9 j "Detachable Power Supply Cords intended for shipment to Original Equipment Manufacturers, shall have any applicable makings provided on the outer surface of the shipping carton, or on a tag or the equivalent inside the carton.  For Detachable Power Supply Cords intended for shipment to original equipment manufacturer, the electrical rating shall be on a tag, or an equivalent, on each individual Detachable Power Supply Cord unless the ampere rating of the flexible cord is equal to or greater than the ampere rating of the attachment plug."9 ]% {* L8 K& x1 |, S2 v
作法:
/ a5 U" u# e  J將有電氣額定規格electrical rating標籤 貼在電源線上
2 \( {/ c, |: Y9 |. J7 M標籤內容字體除高度規定至少1.6mm及字體清晰可見, 標示電流須取最小電流 A 值標示, 範例如下:
8 s1 s1 b$ A3 F) |$ Q. ^; s先核對''UL報告'' 中插頭Plug及尾插Connector及電線cord的通過測試的電流值! |, C/ H: p1 N  ]& D* z! ^) @
Example: NEMA 1-15Plug(15A) + IEC C7 Connector(10A) + No. 18 AWG Flexible Cord(10A)# Q9 \7 ~; K! U/ m

* ~. d/ g1 Q* f  H因為這要求是UL對電源線廠的要求, 電源線廠有義務責任提出符合UL要求的電源線,
板凳
发表于 2010-1-18 15:05 | 只看该作者
多谢楼上的。
地板
发表于 2010-1-19 12:58 | 只看该作者
取暖器是 按照 UL 1278做的吧,如果是最新版本的1278,则需要下面的警告语句,以tag 的形式:( r- G! `4 T' {' i' s% o1 z

' V  x: b) g3 T) T' A
6 Q* H' u2 s8 d/ o( n' f“WARNING – TO REDUCE THE RISK OF FIRE:
& ~# Y7 o% y6 u: \1) Do not place any objects such as furniture, papers, clothes, and curtains closer than
7 }) g- Y& C# H5 t/ ?9 R2 n3 feet (0.9 m) to the front of the heater and keep them away from the sides and rear' ?$ z0 o9 g0 a
when the heater is plugged in.2 }7 O) s% K+ S7 q& d, I7 _
2) Do not place the heater near a bed because objects such as pillows or blankets can
, T0 v& }+ U; Z3 y4 \0 c' G. J, Efall off the bed and be ignited by the heater.
6 m3 W5 {% v7 j3) Always unplug heater when not in use. (This item may be omitted if the heater is& V6 w: u, k  L
provided with a clock-operated switch).8 G, {3 f& ]. s3 {( q- ^% y! O+ q
4) Always plug heaters directly into a wall outlet/receptacle. Never use with an/ J( h. k9 Q1 S/ C5 x- ]+ c) `/ k
extension cord or relocatable power tap (outlet/power strip).
. X2 x- w' [+ c8 X0 ?5) Do not operate heater with a damaged cord or plug or after the heater malfunctions,
% F) q% y/ u' r4 chas been dropped or damaged in any manner. Discard heater or return to an( Y& w6 n8 S, a0 s
authorized service facility for examination and/or repair.: `3 k, r# B) K% h3 w
6) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or9 a& T& b! R; R* j- @5 c
similar coverings. Do not route cord under furniture or appliances. Arrange cord away' b; r8 p2 f5 r1 ?' i
from traffic area and where it will not be tripped over." T: q& X9 F5 Y2 B
7) Check your heater cord and plug connections.# G. u2 C' O  x; |
a) Faulty wall outlet connections or loose plugs can cause the outlet or plug to
8 W' T2 z; k3 S/ f. Voverheat. Be sure the plug fits tight in the outlet.' h+ F1 A: E' M8 @& b$ w; y! e4 e3 i
b) Heaters draw more current than small appliances, overheating of the outlet
& d, S* R( i+ D/ }. o( Emay occur even if it has not occurred with the use of other appliances.  Q" e# |4 }; I; [& Z9 P: _. @
c) During use check frequently to determine if your plug outlet or faceplate is& L& y- P! q2 U/ z- N' Z, r
HOT!
- h8 j7 p6 d7 c- @d) If so, discontinue use of the heater and have a qualified electrician check7 e9 l3 _! W! e# \5 m. b. I- D" j
and/or replace the faulty outlet(s).
' d8 N! F# {' uDO NOT REMOVE THIS TAG!”5 p9 [0 H7 @' h' U9 z8 q
; O3 f! g" J1 y5 E
- i3 n! ^$ W+ a8 O: d

) _" I/ f1 Y: `( I& R2楼的回答,为线方面的,整体并不需要考虑& n& A( Y& P4 a6 _* V1 x
尺寸要求如下:- E  F  l6 U4 w

1 g1 R& C( o2 X4 v( ^# g3 K
1 A" ]$ f4 }6 O1 N0 Q5 X/ O& yThe statements ²WARNING – TO REDUCE THE RISK OF FIRE² and
; A3 H: `( q& w7 O+ _* K²DO NOT REMOVE THIS TAG!² shall be in letters at least 3/16 inch (4.8 mm) in height. The: q) A% }* c( ^. L6 y. c! g1 K
remaining text shall be in letters of at least 1/16 inch (1.6 mm) in height.& g! o% b7 j- I, }
5 D9 Z$ U, y& K: X* x( ~- O
这个 tag需要进行相关测试,可以参考ul 1278的要求
5#
发表于 2010-1-19 13:07 | 只看该作者
也就是标明电流、电压
6#
 楼主| 发表于 2010-1-19 13:25 | 只看该作者
谢谢DX  正如3楼讲解的 客户那边沟通后 给出的要求类似
7#
发表于 2010-1-20 11:26 | 只看该作者
UL的tag有明确要求的  
8#
发表于 2010-1-21 23:01 | 只看该作者
其实做ETL 好点,ETL 报告上都列出了所有标签的要求,同时价格会便宜些。我们工厂的产品客户没有特许要求就做ETL
您需要登录后才可以回帖 登录 | 注册安规

本版积分规则

关闭

安规网为您推荐上一条 /1 下一条

QQ|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网 ( 粤ICP13023453-10 )

GMT+8, 2024-9-21 09:54 , Processed in 0.068416 second(s), 20 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.|广东安规赞助

快速回复 返回顶部 返回列表