安规网

 找回密码
 注册安规
安规论坛 | 仪器设备 | 求职招聘 | 国家标准 公告 | 教程 | 家电 | 灯具 | 环保 | ITAV 签到 充值 在线 打卡 设备 好友| 帖子| 空间| 日志| 相册
IP淋雨机 | 证书查询 | 规范下载 | 资质查询 招聘 | 考试 | 线缆 | 玩具 | 标准 | 综 合 红包 邮箱 打卡 工资 禁言 分享| 记录| 道具| 勋章| 任务
水平垂直燃烧机 | 针焰 | 灼热丝 | 漏电起痕
IP防水防尘设备|拉力机|恒温恒湿|标准试验指
灯头量规|插头量规|静风烤箱|电池设备|球压
万年历 | 距国庆节还有
自2007年5月10日,安规网已运行
IP淋雨设备| 恒温恒湿箱| 拉力机| 医疗检测设备沙特Saber 埃及COI 中东GCC|CoC直接发证机构水平垂直燃烧机|灼热丝|针焰试验机|漏电起痕试验机
灯头量规|试验指|插头插座量规|灯具检测设备耐划痕试验机|可程式恒温恒湿试验箱 | 耦合器设备广东安规-原厂生产-满足标准-审核无忧
查看: 1992|回复: 7
打印 上一主题 下一主题

[美洲标准产品] UL产品的电线警告标签(求助)

[复制链接]
跳转到指定楼层
楼主
发表于 2010-1-18 14:17 | 只看该作者 回帖奖励 |倒序浏览 |阅读模式
广东安规检测
有限公司提供:
我公司有款取暖器 送UL做认证时 要求在电源线上加警告语标签 哪位DX帮帮忙 应该做成什么规格 内容有什么要求吗?在线等
沙发
发表于 2010-1-18 14:38 | 只看该作者
UL817 PROCEDURE SECTION GENERAL 要求:, r6 k. Y, r* Q$ V4 ]) l
    美規US Type 電源線AC Cord, 根據UL817規定從去年2006.06.24 就開始要求, 如下文及附件:
5 B* T( Q+ e- U- Y$ }8 s; F- Y! i0 r
"Detachable Power Supply Cords intended for shipment to Original Equipment Manufacturers, shall have any applicable makings provided on the outer surface of the shipping carton, or on a tag or the equivalent inside the carton.  For Detachable Power Supply Cords intended for shipment to original equipment manufacturer, the electrical rating shall be on a tag, or an equivalent, on each individual Detachable Power Supply Cord unless the ampere rating of the flexible cord is equal to or greater than the ampere rating of the attachment plug."
  x/ l! |: @7 r& U; P作法:
% f. Z5 h  K2 v; u! H將有電氣額定規格electrical rating標籤 貼在電源線上/ I" S* u( h* a9 A
標籤內容字體除高度規定至少1.6mm及字體清晰可見, 標示電流須取最小電流 A 值標示, 範例如下:7 ~; |0 D1 l2 |
先核對''UL報告'' 中插頭Plug及尾插Connector及電線cord的通過測試的電流值$ M  @; X! z0 O/ z7 o- v! Q' \6 f$ b
Example: NEMA 1-15Plug(15A) + IEC C7 Connector(10A) + No. 18 AWG Flexible Cord(10A)
6 n# }6 r' d  w
' R" c+ z/ b6 w" H因為這要求是UL對電源線廠的要求, 電源線廠有義務責任提出符合UL要求的電源線,
板凳
发表于 2010-1-18 15:05 | 只看该作者
多谢楼上的。
地板
发表于 2010-1-19 12:58 | 只看该作者
取暖器是 按照 UL 1278做的吧,如果是最新版本的1278,则需要下面的警告语句,以tag 的形式:6 }# B0 Q0 ]2 v8 Z

" c6 ^& C" z  }! l3 x  c0 a2 M; {; d5 L2 q% m! X) {' E
“WARNING – TO REDUCE THE RISK OF FIRE:$ h$ k5 n0 V/ O5 P, _+ a
1) Do not place any objects such as furniture, papers, clothes, and curtains closer than  _) |% j# |! ?
3 feet (0.9 m) to the front of the heater and keep them away from the sides and rear
+ H/ F2 r: o. F5 Ewhen the heater is plugged in.
: K1 l" Y' W/ y* V7 `. o0 ^2) Do not place the heater near a bed because objects such as pillows or blankets can- M' A* [; [9 U
fall off the bed and be ignited by the heater.
/ z+ M0 v7 K4 Q) z. L3) Always unplug heater when not in use. (This item may be omitted if the heater is
( l! u- i' _5 [$ [+ ?provided with a clock-operated switch).
" P0 m" X9 T& P; T4) Always plug heaters directly into a wall outlet/receptacle. Never use with an; ?9 f& l0 s5 {- a. j$ m' ]
extension cord or relocatable power tap (outlet/power strip).0 L2 y% d: e8 M( N# r
5) Do not operate heater with a damaged cord or plug or after the heater malfunctions,
1 \" L' u7 w& S2 T* z3 ehas been dropped or damaged in any manner. Discard heater or return to an
" k* |6 C  T% l7 I' d1 ?! aauthorized service facility for examination and/or repair.
9 m* P% X6 G& T, c4 w) J# u0 k4 s6) Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
5 K9 }. [* j, U7 Msimilar coverings. Do not route cord under furniture or appliances. Arrange cord away
1 a1 m% m0 o* o! y3 efrom traffic area and where it will not be tripped over.! Y# i3 E1 t% p0 U' V
7) Check your heater cord and plug connections.
& {" Y: d' c% r4 ]6 n% e1 ^a) Faulty wall outlet connections or loose plugs can cause the outlet or plug to
, b# D* V$ v) x+ foverheat. Be sure the plug fits tight in the outlet., T/ x$ W; v5 r  _
b) Heaters draw more current than small appliances, overheating of the outlet
& w0 a9 \1 @/ O4 K  Mmay occur even if it has not occurred with the use of other appliances.% l' L* y- ~8 T; g0 Q7 R7 j) i
c) During use check frequently to determine if your plug outlet or faceplate is
, F* }: H7 s) v) A5 c" T; m# q# bHOT!
+ F7 E# [4 r% y8 U' _d) If so, discontinue use of the heater and have a qualified electrician check
& h; t% N1 j% G' o7 fand/or replace the faulty outlet(s).3 t4 e& ^0 D1 Z( z
DO NOT REMOVE THIS TAG!”4 Q' n: s# y/ d3 g/ `
* I/ D( \0 }) i( [$ q* P
2 X: n5 u- x8 e( C( S

, |" }* I) c# b* A% y+ p2楼的回答,为线方面的,整体并不需要考虑4 o& N! u) l9 ?1 @. H6 `$ q
尺寸要求如下:; N# Q9 y# U, x% _* m7 ~

, B8 T# k2 t/ I) u
. c& [, B( R% ]7 z( N2 I5 HThe statements ²WARNING – TO REDUCE THE RISK OF FIRE² and
4 }7 J1 p/ n5 i8 e" f²DO NOT REMOVE THIS TAG!² shall be in letters at least 3/16 inch (4.8 mm) in height. The+ \; g* }4 G' B& U
remaining text shall be in letters of at least 1/16 inch (1.6 mm) in height.
& y! i* o) l! U" \8 @: O
& h# H  S) |4 @3 H$ p  x这个 tag需要进行相关测试,可以参考ul 1278的要求
5#
发表于 2010-1-19 13:07 | 只看该作者
也就是标明电流、电压
6#
 楼主| 发表于 2010-1-19 13:25 | 只看该作者
谢谢DX  正如3楼讲解的 客户那边沟通后 给出的要求类似
7#
发表于 2010-1-20 11:26 | 只看该作者
UL的tag有明确要求的  
8#
发表于 2010-1-21 23:01 | 只看该作者
其实做ETL 好点,ETL 报告上都列出了所有标签的要求,同时价格会便宜些。我们工厂的产品客户没有特许要求就做ETL
您需要登录后才可以回帖 登录 | 注册安规

本版积分规则

关闭

安规网为您推荐上一条 /1 下一条

QQ|关于安规|小黑屋|安规QQ群|Archiver|手机版|安规网 ( 粤ICP13023453-10 )

GMT+8, 2024-9-20 20:05 , Processed in 0.067588 second(s), 20 queries .

Powered by Discuz! X3.2

© 2001-2013 Comsenz Inc.|广东安规赞助

快速回复 返回顶部 返回列表