|
请注意:澳洲对工具类产品的定义和标准要求为:1 f7 |; E& X4 D; m u9 C; T/ h3 _
Tool – portable type8 q. \: j, y7 t. K/ \
An electrical appliance which:
" I* {% T/ W9 G8 S- L" t• is for machining, drilling, sawing, or surface preparation; and- y! k0 h5 G" @9 b9 X5 @
• may be entirely supported by hand during operation3 k/ h6 V' t3 O% i$ \$ r: ]
but does not include:, \( @- f: @6 p! l) T! A
• a tool, portable type, promoted exclusively to industry.
2 u3 l8 X( B' i h( [( c* n! D; s• Class specification: a heat pump.
% x& X, F' F, M5 jDrill
8 o. I# |; [0 S" R- x! k# H
4 a8 R) G; x: ^. S+ L ~! VAS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.1:2003.
, U: m' @# Q. d/ | f- N: GSander or polisher (other than disk types)" [" A9 h- b. T, U1 l
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.4:2003.0 \9 @' ?, d/ s$ W
Circular saw( z! P* w! d, A; E
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.5:2003.
8 _9 m: Y" Q4 ]; Z5 C' n$ P. C6 YJig or sabre saw2 z9 e! [" o" u0 r- c/ y
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.11:2003.
# N5 h5 n0 B' r3 K9 b& g) fPlaner- n' O" N0 O2 [4 D' N) \
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.14:2003.# H# X& d1 x/ B; d) L+ U% |
Router
* t9 C! U0 x/ o+ MAS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001 (until 14 November 2006) or AS/NZS 60745.1:2003 and AS/NZS 60745.2.17:2003.
f+ |' J% ~1 s- f& T- P9 m+ JOther7 a W+ u% D6 e- \' b/ h
AS/NZS 3100:2002 with amendment 1 and AS/NZS 3160:2001.0 w' r1 [* y8 V8 J8 R
1 Y: g1 d, ~7 f0 b
台式工具并不属于以上范围,只能申请自愿认证,而且因为没有相应的澳洲标准,所以只能由认证部门说了算。 |
|